0
Both. When an AC voltage is measured and a number is reported, it is necessary to state that this number is rms value or peak value or peak to peak value.
AnswerVoltages and currents are each normally expressed in root-mean-square (rms), unless otherwise stated. For example, when we talk about a '120-V service' or a '240-V service', we are expressing the voltages in rms values; it is unecessary to specify that these are rms values. For a sinusoidal waveform, Vrms = 0.707 Vpeak
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is the peak-to-peak voltage in a circuit with an rms voltage of 120VAC?
ANSWER: The peak to peak voltage can be found by multiplying 120 v AC x 2.82= 339.41
What is peak to peak voltage?
Conversions of RMS voltage, peak voltage and peak-to-peak voltage. That are the used voltages. The expression "average" voltage is used for RMS voltage.Scroll down to related links and seach for "RMS voltage, peak voltage and peak-to-peak voltage".Answer'Average' is not the same as 'root mean square'. As the average value of a sinusoidal voltage is zero, you cannot convert it to a peak-to-peak value.
Where are Vpp and V rms?
Vpp is Peak-to-Peak voltage, in other words, in AC voltage, the peak-to-peak voltage is the potential difference between the lowest trough in the AC signal to the highest. Assuming the reference to the voltage is zero, Vpp would be twice the peak voltage (between zero and either the highest or lowest point in the AC waveform). Vrms is the Root Mean Square voltage, think of it as sort of an average (it's not quite that simple). For a sine wave, the RMS voltage can be calculated by y=a*sin(2ft) where f is the frequency of the signal, t is time, and a is the amplitude or peak value.
What is the peak-to peak voltage of a 56 Vrms ac voltage?
For a sine wave, the form factor is the square root of 2. Thus, the effective voltage of 56 V (56 Vrms) is 2-1/2 times the peak-to-peak voltage. Thus, the peak-to-peak voltage Vpp = Vrms * sqrt(2)In this example:Vpp = 56V * 1.4142... = 79.2V (rounded to one decimal place)
What is the relationship between peak to peak and peak voltage for a sine wave?
The RMS (root mean square) of the peak voltage of a sine wave is about 0.707 times the peak voltage. Recall that the sine wave represents a changing voltage, and it varies from zero to some positive peak, back to zero, and then down to some negative peak to complete the waveform. The root mean square (RMS) is the so-called "DC equivalent voltage" of the sine wave. The voltage of a sine wave varies as described, while the voltage of a DC source can be held at a constant. The "constant voltage" here, the DC equivalent, is the DC voltage that would have to be applied to a purely resistive load (like the heating element in a toaster, iron or a clothes dryer) to get the same effective heating as the AC voltage (the sine wave). Here's the equation: VoltsRMS = VoltsPeak x 0.707 The 0.707 is half the square root of 2. It's actually about 0.70710678 or so.
What is an RMS output?
That is an electric AC or audio output, where the voltage is measured in volts rms. Scroll down to related links and look for "dB conversion (decibel)". Look there in the middle at this headline: "RMS voltage, peak voltage and peak-to-peak voltage".
What is the peak-to-peak voltage in a circuit with an rms voltage of 120VAC?
ANSWER: The peak to peak voltage can be found by multiplying 120 v AC x 2.82= 339.41
Why you take 2Vm peak inverse voltage for full wave rectifier?
When the AC waveform goes to one peak, the capacitor that follows the diode is charged to that peak value. When the AC waveform goes to the other peak, the same diode is reverse biased between the alternate peak value and the charged value of the capacitor. This differential voltage is two times peak voltage.
What is the peak voltage of a sine wave that measure 220V AC rms?
Peak voltage will be 1.414 times the RMS. Peak to Peak voltage, assuming no DC offset, will be 2 x 1.414 x the RMS value.
What is peak to peak voltage?
Conversions of RMS voltage, peak voltage and peak-to-peak voltage. That are the used voltages. The expression "average" voltage is used for RMS voltage.Scroll down to related links and seach for "RMS voltage, peak voltage and peak-to-peak voltage".Answer'Average' is not the same as 'root mean square'. As the average value of a sinusoidal voltage is zero, you cannot convert it to a peak-to-peak value.
What is the peak to peak voltage for the AC line voltage in normal outlets of your house?
Peak - neutral for 120 volts RMS is 169 volts, or 120 * sqrt(2) Peak to peak will be 2 x this value, or 339 volts.
Where are Vpp and V rms?
Vpp is Peak-to-Peak voltage, in other words, in AC voltage, the peak-to-peak voltage is the potential difference between the lowest trough in the AC signal to the highest. Assuming the reference to the voltage is zero, Vpp would be twice the peak voltage (between zero and either the highest or lowest point in the AC waveform). Vrms is the Root Mean Square voltage, think of it as sort of an average (it's not quite that simple). For a sine wave, the RMS voltage can be calculated by y=a*sin(2ft) where f is the frequency of the signal, t is time, and a is the amplitude or peak value.
What is the peak-to peak voltage of a 56 Vrms ac voltage?
For a sine wave, the form factor is the square root of 2. Thus, the effective voltage of 56 V (56 Vrms) is 2-1/2 times the peak-to-peak voltage. Thus, the peak-to-peak voltage Vpp = Vrms * sqrt(2)In this example:Vpp = 56V * 1.4142... = 79.2V (rounded to one decimal place)
Use of RMS?
I am not certain what is being asked here. RMS is Root Mean Square which is basically the DC voltage which would produce the same amount of heat in a heating element as the AC voltage in question. Since AC is continuously changing in polarity and voltage, it is handy to use the RMS voltage rather than the peak (169.7V for 120V RMS) or peak-to-peak (339.4V for 120V RMS). The peak or peak-to-peak voltage is handy to know when considering the maximum values such as in rectification.
How to calculate the peak-to-peak value of a signal?
A: AC or our line voltage is sinusoidal in nature it goes up to a positive peak returns to zero and proceed to the negative peak. 120V AC is actually swinging from peak to peak. It is 120 volts but the peak is the 120 v times 1.41 or 169.2 volts and since it also go negative then the peak to peak 120 volts times 2.82 or 338.40 volts or twice the peak voltage
Why is the class A current less than the peak current?
Not sure what you mean by Class A current. Normally, when measuring AC voltage or current you either measure the peak to peak value or the Root Mean Squared (RMS) value. Since RMS is essentially an average measured over time, it would always be less than Peak to Peak value.
How rms voltage related to peak voltage?
The average voltage is the rms voltage.Volts peak = volts RMS times 1.414Volts RMS = volts peak times 0.7071Use the link below to an RMS voltage, peak voltage and peak-to-peak voltage calculator.********************************The average voltage is not the r.m.s. voltage.The average voltage of a sine wave is 0.636 x the peak value. Conversely, peak voltage is 1.57 the mean or average.
