A: AC or our line voltage is sinusoidal in nature it goes up to a positive peak returns to zero and proceed to the negative peak. 120V AC is actually swinging from peak to peak. It is 120 volts but the peak is the 120 v times 1.41 or 169.2 volts and since it also go negative then the peak to peak 120 volts times 2.82 or 338.40 volts or twice the peak voltage
To calculate the percent signal from a given current, you typically need a reference value, often the maximum current for a 100% signal. Assuming a common reference maximum of 20 mA (used in many industrial applications), you can calculate the percent signal as follows: [ \text{Percent Signal} = \left( \frac{11.3 , \text{mA}}{20 , \text{mA}} \right) \times 100 = 56.5% ] Thus, an 11.3 mA signal corresponds to approximately 56.5%.
A: Practically all of the bridges used to find the value of passive components uses a null signal to determine the value In reality null means the lack of a signal where it is virtually eliminated when that occurs that is the null or no signal.
to calculate and measure the impedance ,admittance is simple
what is the diference betwean calculated and maesured value
The DC value of an AC signal, often referred to as the average or mean value, represents the constant voltage level that would produce the same power as the AC signal over a complete cycle. For a pure sinusoidal AC waveform, the DC value is zero because the positive and negative halves of the waveform cancel each other out. However, for waveforms that are not symmetrical, the DC value can be calculated as the average of the signal over one complete cycle. It is essential in applications where the effective power or energy delivery needs to be assessed.
To determine the amplitude of a sinusoidal signal, we look at the peak value of the signal function. The amplitude is the half of the peak-to-peak value of the signal, or the absolute value of the maximum value of the signal.
To calculate the percent signal from a given current, you typically need a reference value, often the maximum current for a 100% signal. Assuming a common reference maximum of 20 mA (used in many industrial applications), you can calculate the percent signal as follows: [ \text{Percent Signal} = \left( \frac{11.3 , \text{mA}}{20 , \text{mA}} \right) \times 100 = 56.5% ] Thus, an 11.3 mA signal corresponds to approximately 56.5%.
Calculate the capacity of a telephone channel of 3000hz and signal to noise ratio of 3162?
To calculate the intermediate frequency (IF) for a radio receiver at 70 MHz, you typically choose a fixed IF value such as 455 kHz or 10.7 MHz. The IF frequency is chosen in such a way that when the desired signal frequency (70 MHz) is mixed with the local oscillator signal, it falls within the receiver's bandwidth for demodulation. This allows for effective filtering and processing of the signal at a manageable frequency before demodulation.
there is no value. its baseball.
It can be calculated by simplifying the ratio between power of signal by power of noise
The unit step signal is a Power signal. Since when we find the power it comes to 1/2 (i.e finite value). And when we find its energy, we got INFINITY. If a signal has energy as infinity and power as a finite non-zero value, then it is a power signal, not an energy signal.
What is the formula to calculate the value of cell J10?
If the AC signal is sinusoidal, then the RMS value is 141 divided by square root of 2, i.e. 99.7 volts.
To calculate the salvage value of equipment, subtract the estimated cost of disposing the equipment from its current market value.
A: Practically all of the bridges used to find the value of passive components uses a null signal to determine the value In reality null means the lack of a signal where it is virtually eliminated when that occurs that is the null or no signal.
An analog signal is a continuous signal that contains time-varying quantities. Unlike a digital signal, which has a discrete value at each sampling point, an analog signal has constant fluctuations. netonplus.com