0
Like an automatic indicator? If that's what you mean, you already have one in your car. The indicator will turn off when you have finished turning. It shouldn't take much to change it so it activates when you start turning. However such a device would not be practical (or safe) for use on the roads, as it would not give enough prior warning to other drivers.
What else can I help you with?
What condition that refers to any input into a circuit from changes in a system?
Automatic
What is strobe signal?
A strobe signal is the name for any signal that flashes on and off. For example the turn-lights on a car. Certain lights such as some leds aren't actually on all the time but flash faster than the eye can see, that is also a strobe signal.
What is the importance of convolution in system characterization?
Convolution is used in DIGITAL SIGNAL PROCESSING to predict the output of the system with only a few limited number of samples of the input signal and a few limited number of samples of the impulse response of the system. i.e. if we can state that if you know the impulse response of a system then you can predict the behavior of the system for any signal provided it as an input. It also helps to show that the system is stable or not i.e. we say that a system is stable if its impulse response is absolutely summable or square summable (both are sufficient conditions but not necessary conditions).
Difference between strobe and handshake signal?
A strobe signal is sent by the signal sender without any regard to the signal receiver. This assumes that the design provides sufficient setup and hold time, along with transmission time, to ensure reliable receipt of the signal. A handshake signal is a bi-directional protocol between the signal sender and the signal receiver, which the receiver uses to tell the sender that the signal has been received. In this system, it often does not matter what the transmission time is, but bandwidth can be reduced since the sender must wait for the handshake to come back from the receiver, effectively doubling the time it takes to send a signal.
Why is an automatic toaster open loop system?
since i doesnt take any feedback and the bread pops out as soon as the time is over. whether the bread was toasted or not is not seen, hence it is open loop.
How to fix turn signal problem on Mitsubishi Montero LTD 2002?
To fix a turn signal problem on a 2002 Mitsubishi Montero LTD, first check the turn signal bulbs for any burnouts and replace them if necessary. Next, inspect the fuses related to the turn signal system; if any are blown, replace them. If the issue persists, examine the turn signal switch and wiring for any signs of damage or corrosion. If you're unable to diagnose the issue, consider consulting a professional mechanic for further assistance.
How do you fix a turn signal when the hazard lights blink left turn signal blinks but when using right turn signal it just stays on on a Dodge Dakota?
Sounds like you simply have A burned out bulb, Turn the signal on and look at all the lights to see if any are burned out. Could be A marker light if its in the turn signal circuit.
Turn signal switch affect broken cruise control?
It's the the turn signal switch that controls the Cruise Control Assembly. Therefore any problem to the Turn Signal switch affects the whole road safety.
How do you repare turn signal lights on a ford focus?
I am assuming you have replaced any defective bulb. If none of the turn signals work, replace the turn signal flasher relay.
How do you fix a turn signal on a Nissan Frontier?
To fix a turn signal on a Nissan Frontier, first, check the turn signal bulb to see if it's burned out; if so, replace it with a new bulb. If the bulb is fine, inspect the turn signal fuse in the fuse box for any damage and replace it if necessary. Additionally, check the turn signal relay and wiring for any faults. If these steps don't solve the issue, consider consulting a mechanic for further diagnosis.
How do you replace the turn signal bulbs on a 1997 Dodge Ram?
my left turn signal on my 1997 dodge conversion van works fine,the right signal lights but does not blink,,,,any ideas
What could be the problem if the Turn signals do not blink when switched on in your 66 cadillac bulbs are all good any ideas?
Faulty Turn Signal flasher Faulty Turn Signal Switch
How would you signal to turn left while driving?
To signal a left turn while driving, activate your left turn signal by using the turn signal lever, which is typically located on the left side of the steering wheel. Ensure that the signal is clearly visible to other drivers and pedestrians. Before making the turn, check your mirrors and blind spots for any oncoming traffic or obstacles. Finally, proceed to make the turn when it is safe to do so.
How do you fix a stuck turn signal?
To fix a stuck turn signal, you may need to replace the whole switch. A switch can be purchased at any auto parts store.
Is there any way to turn off the automatic headlamp system on the GM Yukon 2003?
If there is, it will be listed in your owner's manual. Depress the push button on the light panel 4 times.
Why would Only 1 brake light work and that's the one in the rear window any suggestion?
You almost certainly have bulbs burnt out. Answer 2: Check the fuses, as well as the bulbs. If all that is good AND your system uses the same light (Brake Light) for the turn signal, then check the turn signal switch as well (the brake light lead passes through the turn signal switch). If that is all good, or it is a different system, then check the wire leads running into the rear section; most have plugs that could have become disconnected.
Is it against the law to make a left or right turn without using your signal light in California?
It's unlawful to make any turn without using your turn signal. That's why they're there. They aren't just for decoration.
