answersLogoWhite

0

What else can I help you with?

Continue Learning about Electrical Engineering

The most commonly used wiring method is?

The most commonly used wiring method for residential use is called nonmetallic sheathed cable. Other types of wiring methods are knob and tube, as well as service entrance cable.


What is the difference between type ac and type act armored cable?

The difference is the type of insulation on the conductors. Type AC used a thermoset insulation , Type ACT is a theromplactic insulation.


Why single-core cable armoured with steel wire or tape must not be used for a c circuit?

Current in the single core cable would induce a magnetic current in the steel cable, though a transformer effect. This would heat the steel armored strands, and the circuit would increase more electrical power from the load supply point. The earthing of the cable glands would complete the circuit and the return current would flow in the earth bonding cable between the two points. This is called Eddy currents generated in the cable by the twist of the steel armored around the central core, current flowing in one direction


Does commercial electrical wiring have to be in conduit if it is behind a wall covering?

It depends on whether the building classification is combustible or non combustible. On a new commercial building wiring is usually designed by an electrical engineer. In this case the wiring is done to their specifications. On a rewire of a commercial building BX cable can be used behind wall board. The reasoning is that most commercial buildings these days use steel studs. Dragging ordinary NMD wire through these types of studs can cut the outer sheath. In some jurisdictions steel stud bushings have to be used when a steel stud is hole punched. By using this type of wiring cable, rigid conduit or EMT does not have to be used.


Identify materials that are commonly used as conductors to provide household electricity?

Non metallic sheathed cable is used as conductors in home wiring.See related links below.

Related Questions

What was used before romex wire became available?

Before Romex wire became available, cloth-covered wire, knob-and-tube wiring, and armored cable (BX) were commonly used for electrical wiring in residential buildings.


Where are armored cables and unarmored cables used?

Armored cable is used in environments such as a front yard where environmental conditions make an armored cable susceptible to damage. If the question is asking about Shielded/Screened cable, that has a small thin metal foil wrapping that is used to "screen out" most external signal noise from the cable.


What meant by armored cable and why it is used?

For protection of the wires.


When armored cable is used what protection is used at the end?

Mac anntena


What is single core armored cable?

Armored electrical cable contains insulated electrical service wires protected by a flexible steel covering. Unarmored electrical cable has no protective flexible steel covering, its covering is made of plastic. <><><> Armored cable (BX) is the older version of Metal Clad cable (MC). It was flexible steel covered wire that used the steel as it's Ground. BX was a poor grounding system so it was replaced with MC which looks similar but has a separate Grounding conductor. MC is most often made with aluminum as its cover. Armored cable if used today will refer to MC type wiring. <><><> Some kinds of armored cable are in fact made to a tougher standard than the ordinary soft wire strand types of shielded cable that are used for hooking-up antennas. The 'armor' is actually a thin flexible metal film that better protects the wire or wires inside from damage in high use or high traffic areas. Such kinds of armored cable are also used in radio frequency assemblies in electronic equipment.


What is SWA when used to describle an electric cable?

Steel Wire Armored.


What is armored cable made from?

Armored electrical cable contains insulated electrical service wires protected by a flexible steel covering. Unarmored electrical cable has no protective flexible steel covering, its covering is made of plastic. <><><> Armored cable (BX) is the older version of Metal Clad cable (MC). It was flexible steel covered wire that used the steel as it's Ground. BX was a poor grounding system so it was replaced with MC which looks similar but has a separate Grounding conductor. MC is most often made with aluminum as its cover. Armored cable if used today will refer to MC type wiring. <><><> Some kinds of armored cable are in fact made to a tougher standard than the ordinary soft wire strand types of shielded cable that are used for hooking-up antennas. The 'armor' is actually a thin flexible metal film that better protects the wire or wires inside from damage in high use or high traffic areas. Such kinds of armored cable are also used in radio frequency assemblies in electronic equipment.


What does bx mean in electrical terminology?

In electrical terminology, "bx" refers to a type of armored cable commonly used for wiring installations. It is a flexible metal-clad cable that provides mechanical protection and grounding for electrical conductors.


Can you use armored cable to wire 277 volt lights?

Yes, armored cable can be used to wire 277 volt lights. However, be sure to select the appropriate type and size of armored cable rated for the voltage and current requirements of the lighting system to ensure safety and compliance with electrical codes and regulations.


What is an armored wire?

A cable with a steel sheath.AnswerArmoured cables are cables designed to by laid underground. An armoured cable is a cable whose conductors are protected from mechanical damage by an outer layer of steel tapes or wire. The armour itself is protected against corrosion by an outer waterproof layer. The steel tape or wire is wound around the cable to maintain its flexibility.


What is the maximum voltage rating for AC-90 armoured cable?

The maximum voltage rating for AC-90 armored cable is typically 600 volts. This type of cable is designed for use in various applications, including building wiring and power distribution, and is suitable for both indoor and outdoor installations. It's important to ensure that the cable is used in accordance with local electrical codes and standards.


The most commonly used wiring method is?

The most commonly used wiring method for residential use is called nonmetallic sheathed cable. Other types of wiring methods are knob and tube, as well as service entrance cable.