0
Armored electrical cable contains insulated electrical service wires protected by a flexible steel covering. Unarmored electrical cable has no protective flexible steel covering, its covering is made of plastic.
<><><>
Armored cable (BX) is the older version of Metal Clad cable (MC). It was flexible steel covered wire that used the steel as it's Ground. BX was a poor grounding system so it was replaced with MC which looks similar but has a separate Grounding conductor. MC is most often made with aluminum as its cover.
Armored cable if used today will refer to MC type wiring.
<><><>
Some kinds of armored cable are in fact made to a tougher standard than the ordinary soft wire strand types of shielded cable that are used for hooking-up antennas. The 'armor' is actually a thin flexible metal film that better protects the wire or wires inside from damage in high use or high traffic areas. Such kinds of armored cable are also used in radio frequency assemblies in electronic equipment.
What else can I help you with?
The center copper core of coaxial cable is called what?
Coaxial cable has a center core of copper wire surrounded by a layer of insulation, which is in turn surrounded by a conductive braided shielding and encased in a final insulation sheath. The center copper core and the braided shielding layer act as two independent conductors, thus allowing two - way communications over a coaxial cable.
What is the duration of Armored film?
The duration of Armored - film - is 1.47 hours.
What is the current rating of 25mm 4-core armoured cable?
You have to be specific. whether the conductor is aluminum or copper. Current carrying capacity will be different for these two types. Copper cable can take more load than aluminum cable for same diameter.
What is the motto of Armored Corps Israel?
The motto of Armored Corps - Israel - is 'The man in the tank will be victorious'.
What is the limitation of length for category 5 UTP network cable?
For a single link the maximum is 100 meters.
Why single-core cable armoured with steel wire or tape must not be used for a c circuit?
Current in the single core cable would induce a magnetic current in the steel cable, though a transformer effect. This would heat the steel armored strands, and the circuit would increase more electrical power from the load supply point. The earthing of the cable glands would complete the circuit and the return current would flow in the earth bonding cable between the two points. This is called Eddy currents generated in the cable by the twist of the steel armored around the central core, current flowing in one direction
When did Armored Core V happen?
Armored Core V happened in 360.
What does ACSIS mean in armored core 4?
"Armored Core Schematic Interface System"
Is Armored core 4 for the Xbox 360 already in stores?
Yes armored core 4 has been in stores for awhile. the sequal armored core for answers is out as well
What is single core cable used for?
dont know mate
What is non-armored cable?
Cable that has no armor.
Can you play Armored core 1 on PSP?
no but you can play armored core formula front on psp
When was Armored Core V created?
Armored Core V was created on 2012-01-26.
How do you install an electrical circuits wiring using armored cable?
Same installation as non armored cable.
What is the difference between armored cable and mc cable?
The difference between Armored cable and Metal Clad cable is that the MC cable has a EGC (Equipment Grounding Conductor). Both cables are armored, and look almost identical so watch out.
What was the general reception of 'Armored Core 4'?
The general reception of 'Armored Core 4' was very good. The general reception of 'Armored Core 4' was met with a dedicated fanbase full of many supporters.
Why would four core armoured cable be used in a single phase circuit?
Four core armoured cable would be used in a circuit carrying 240 Volts 60 Hz AC that is installed in a location where it could get damaged, such as underground or under water. The 4 cores in the armoured cable would be used as the following conductors for the 240 V 60 Hz circuit: * "Red" hot (120V above Neutral)* "Black" Hot (120V below Neutral)* "Neutral"* "Ground" to protect the circuit, connected to the main incoming supply panel which feeds the circuit.
