An electric wall heater can be placed anywhere. Make sure there is 2 feet of space in front of the heater to avoid fires.
Place the heater where there is not much foot traffic so there won't be any danger of it being tipped over. Also if you have small childen consider putting it where they won't have access to it as it can burn them.
Take the plug in your hand, and insert the plug into the wall outlet.
This is a 240 volt, two chimney heater (1500 watts per chimney) with a double pole thermostat. If the heater is not heating at all, indicates thermostat or electric source issue, if one element is heating and second is not, indicates one of the elements is burned out.
Installing a wall scone with an electric light can be an easy process. First the power must be turned off to prevent electric shock. Then a hole should be cut to fit the fixture and expose the wires. Match up the correct wires to the light then place the sconce in the wall. Secure the sconce with glue or nails and test the light connections.
Courtesy of Ace Hardware - I found it on their site · What is the difference between a double pole and a single pole thermostat?Single pole thermostats breaks only one side of the power line to your heater and cannot be turned off. Therefore, power is continuous to the heater even if it is not running. The control knob will have a low temperature setting without an off position. Single pole Thermostats uses only two wires. This means that even if the temperature dial is turned all the way down, voltage is still going into the heater through one line. This may pose a hazard to anyone who might perform electrical work on the heater without realizing that the circuit was still on. You will need to turn off the power at the circuit breaker before electrical repairs can be made safely.Double pole thermostats breaks both sides of the power line; therefore all power to the heater is interrupted. This acts as a safeguard for people performing electrical work on the heater. However, to be on the safe side, you should always turn off the power at the circuit breaker, not at the thermostat, before making any electrical repairs. A double pole will uses four wires and has a off position on the thermostat.Since they are inherently safer, you should always try to use double-pole thermostats, if possible. Another advantage of a double-pole thermostat is that you can turn it completely off and the heat will not come on no matter how cold your room gets. But with a single-pole unit, the thermostat will turn the heat on even if set on the lowest setting.CHECK YOUR LOCAL CODES FOR BUILDING REQUIREMENTS IN DETERMINING IF YOU NEED A SINGLE OR DOUBLE POLE THERMOSTAT BEFORE PURCHASING OR INSTALLING. How can I determine if I have a single or double pole thermostat?Usually, you can tell the difference between a single pole and double-pole thermostat by looking at the dial. A double-pole normally has an "Off" position on the dial whereas a single-pole thermostat does not. The only sure way to tell which kind you have is to remove it from the wall and count the wires connected to it. A double-pole thermostat will have four wires that switches both hot wires whereas a single-pole thermostat will have two wires that only switches one of the hot wires. Can I use a single or double pole thermostat with a 120, 208, or 240 volt heater?Yes. Can I use 1 thermostat to control more than 1 baseboard heater?Built-in thermostats (mounted directly on baseboard) are designed for single heater use. However, it is possible to control more than 1 heater on a wall thermostat if the thermostat rating is not exceeded. Can I mount the thermostat on one side and wire the baseboard heater on the opposite side?No, the thermostat requires power from the supply wires and must be wired in conjunction with the baseboard heater. Is a built-in or a wall mount thermostat better?A built-in control is convenient when the walls are already finished. The built-in thermostat is also convenient to install. However, the wall thermostat is a more accurate way to control the room temperature, is more convenient to use, and has a broader selection of models. The use of electronic thermostats provides more accuracy and saves you money on your electric bill. Can all of the heaters in my house be controlled by one thermostat?There are many benefits to zonal heating. Zonal systems save energy by not heating unoccupied rooms and provide the ultimate in comfort by allowing occupied zones to be heated specifically to individual needs. The purpose of each zone's (room) heater is to heat that specific zone per the set point of the individual thermostat. What is the difference between a low voltage and a line voltage thermostat?Low voltage thermostats should be used when the heater load is greater than 3,800 watts such as commercial heater or central forced air systems.Line voltage thermostats should be used for zonal heat systems such as electric fan heaters, baseboard heaters and radiant heaters. What should I do if my wall thermostat feels hot to the touch?Cadet recommends you replace the thermostat. A hot thermostat indicates that it is not working efficiently; decreasing its accuracy. NOTE: A normal operating thermostat will be slightly warmer than the room temperature by 3 to 5 degrees. Can I use a wall mount thermostat to control my heater if it has an in-built thermostat?Yes, to bypass the in-built thermostat, turn the thermostat on the heater to the highest setting, then use the wall thermostat to regulate the room temperature.
Are you talking about recepticale boxes that you plug a device into or service panel that the breakers are in?
Before buying electrical wall heater you must know about your electrical supply, connections and wiring. The wiring should be able to bear additional high current and supply should have capacity for extra wattage. The walls and contacts should be properly insulated and free from moisture. There should be tripping safety mechanism in wall heater.
A micathermic heater is used where there is not much space to place a conventional heater. They can be mounted on a wall like a picture which saves foot space.
You should keep your indoor heaters several feet from the wall, or as far as you possibly can without moving it in the way of everything. You definitely don't want your wall to get too hot for safety reasons. At a minimum, make sure that you place your indoor heater three feet away.
To stop the black residue from a baseboard heater, the wall around and near the heater should be cleaned as there are dust particles attached to the wall. This is called ghosting which fine particles of soot attach to the wall that is cooler than the temperature.
To install a wall heater, first choose a suitable location on the wall. Make sure there is proper clearance around the heater. Next, mount the heater on the wall using the provided hardware. Connect the heater to the electrical supply following the manufacturer's instructions. Finally, test the heater to ensure it is working properly and safely.
If you have a home that was built a long time ago, you might have a room that does not have any heat directly put into them, or you might simply want to include more heat into a room that does not seem to get enough. Whatever the reason, you may benefit from installing a Com-Pak wall heater in the room that needs more heat in it.The first thing you must do is figure out where you will install the wall heater. You do not want it to be within half a foot of any kind of surface or fixture, and if you want to simplify the steps of wiring, you would ideally place your wall heater near an outlet.Measure how large your heater box is, or you can instead use the measurements that are listed in the directions. Wherever you plan to install the wall heater, you should then outline your box on the wall. Use a drywall saw to trace the outline and cut the hole.Once this has been done, you can remove the cover where the outlet is going to wire and take the outlet out of its packaging. Take out the corners of the box so you can run the wires through.Use a pair of screws to affix the box to the hole you cut earlier. Take the wire and place it through the corner of your wall box. Before you connect it to the outlet, you should connect it to the heater first.Take the heater that you have inserted into the box in the wall and affix it using the screw that the packaging came with. After you have done this, you can replace the cover on the heater in the box in the hole and take the screws to secure its position in the wall so it will hold the cover.Lastly, you will need to take the wires and affix them to the outlet. After you do this, you should put them back together with the cover just like you originally found them before beginning this project. You should now be able to function your heater with a simple knob.
The steps involved in wall heater replacement typically include turning off the power, removing the old heater, installing the new heater, connecting the wiring, securing the unit in place, and testing to ensure it is working properly. It is important to follow manufacturer instructions and safety precautions throughout the process.
should be on the passenger side right along the fire wall
The steps involved in wall heater installation typically include: Choosing a suitable location for the heater on the wall. Ensuring proper electrical or gas connections are available. Mounting the heater securely to the wall. Connecting the heater to the power source. Testing the heater to ensure it is working properly. Following manufacturer's instructions for any additional steps or safety precautions.
It should be placed 2 ft from the wall
An electric wall heater is the perfect solution for houses in areas that have mild winters. The heater will provide heat for the rooms around it, and it should be installed on a wall that is central to the whole house. Electric wall heaters have some good features and some bad features. Targeted Heat Usually an electric wall heater is a panel that runs from just below the ceiling to just above the floor. It radiates heat to all of the air that directly surrounds it. If you need to heat a three bedroom house, an electric wall heater may not have the strength to reach every room. If your house or apartment is smaller, however, an electric wall heater may be just what you need to keep a couple of the bedrooms and the bathroom warm. Where you place the heater will have a definite impact on how well it heats your rooms. Uses Less Electricity than Central Heating Central heating is designed to heat your entire house. It uses the thermostat to determine when to turn off and on, and it pushes warm air into every room through a ducting system. An electric wall heater doesn’t attempt to warm the entire house. It only warms the air in a radius around the heater. Heating is more immediate with an electric wall heater, so you don’t have to wait hours for it to heat the room. Since you have tighter control over when an electric wall heater is off or on, the heater consumes less electricity and delivers targeted heat when you need it. Easy to Control An electric wall heater is a very straightforward device. When the house is cold, all you have to do is turn it on. The room will start to get warmer immediately. When a room is too warm, all you have to do is turn off the wall heater and the room will begin to cool immediately. The air around an electric wall heater is not pushed around the room, so it remains warmer than if it were blowing through a vent. Electric wall heaters become very hot when they are in use, so keep children a safe distance away from the heater.
Disconnect the heater lines going into the fire wall from under the hood. Remove the panels from under the dash. At this point you should be able to remove the heater cover and remove the heater core.