answersLogoWhite

0

3 components ;

voltage supply or battery

connection wires or wiring

a lamp bulb to indicate presence of current flow within the circuit

when current is actually flowing within the wires.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Electrical Engineering

What is the design procedure for clamping circuits?

Clamping circuits use diodes and capacitors. First, the first circuit must be set up, then a?æsine wave should be input into it. The input and output should be observed and adjusted as necessary; then, the process should be repeated for the other circuits.


What must happen for an electric motor to spin?

suitable winding and correct power supply


What electrical wiring is required when fitting a new kitchen?

AWG 12/2 wire on a 20 amp breaker. There must be 2 kitchen outlet circuits and each circuit must be protected with a GFCI outlet. Each of these items must be on it's own dedicated 20 amp circuit. Garbage disposal, dishwasher, microwave, refrigerator. This will require 6 dedicated 120 volt 20 amp circuits plus a 240 volt 60 amp circuit for the range.


Can you run 2 different circuits through the same junction box?

Yes, you can run two different circuits through the same junction box, provided that the box is large enough to accommodate the wires and connections without overcrowding. Each circuit must have its own separate circuit breaker in the panel, and it's important to ensure that the circuits do not overload the junction box. Additionally, all local electrical codes and regulations must be followed to ensure safety and compliance. Always consult a licensed electrician if you're unsure about your specific situation.


What equivalent size electric motor will replace a 8 HP gasoline engine?

If the gasoline engine must supply energy at the rate of 8 horsepower to its load, then so too must the electric motor. Expressed in watts, 8 horsepower is equivalent to 6 kilowatts. So the output power of the motor must be 6 kilowatts.

Related Questions

What are the three basic features all electric circuits must have?

Three things that an electrical circuit must have to operate is, A) a source. Example- battery B) a line. Example- conducting wires that allow the electricity to pass through and C) a load. Example- A light bulb


What opposing force must be overcome by charges flowing in electric circuits?

The opposing force that charges flowing in electric circuits must overcome is resistance. Resistance is caused by factors such as the material through which the charges are flowing, the temperature of the material, and the dimensions of the material. It impedes the flow of charges and results in the conversion of electrical energy into heat energy.


What do you mean by quantisation of charge?

The principle that the electric charge of an object must be part of a divisible basic axiom.


Why you need electronic?

We need to use electric circuits so as to make the transfer of electricity easier. you must have seen various paths made in the circuits, these path controls and regulates the flow of current . But if we don't use electronic circuits then we will have to use wires which is very difficult to handle when we have to do large no. of operations li in computer.


5 features of habitat?

The five features of a Habitat is that It must have a Sustainable water supply It Must have a endurable weather condition It must have the basic quality of the a habitat for organism It must have the food quality that the organism feed on It must have a long term duration


What appliances must be supplied by and individual branch circuit?

Appliances that must be supplied by individual branch circuits include large devices such as refrigerators, electric dryers, washers, and ovens. Additionally, dedicated circuits are typically required for certain heating and cooling systems, such as air conditioners and electric water heaters. This ensures that these high-demand appliances operate safely and efficiently without overloading the circuit. It's important to adhere to local electrical codes and regulations for proper installation.


What are the two basic types of electric circuits?

There are many different types of circuits, but, in basic electricity, perhaps the two most common types of circuits are parallel and series.A parallel-connected circuit is one in which the current divides into two or more flows with at least one load on each flow, whereas a series circuit has only one flow that passes through two or more consecutive loads. The input voltage to a parallel-connected circuit stays constant - so every branch of the circuit gets the same voltage from the power supply - but there is a different current flowing in each branch dependant on the resistance of the loads in that branch. Overall, no current gets lost because any current entering a particular junction (leading to branches) is always equal to the current leaving that junction.In a series-connected circuit the input current stays constant and the voltage is divided amongst the loads which are connected like links in a chain: each load component (a light, a resistor, etc.) is connected "head to tail" to the next one in the series circuit.A more complete answerActually there are four types of circuit, not two. These are series circuits, parallel circuits, series-parallel circuits, and complex circuits.'Complex circuits' (which are not necessarily complicated) describe any circuit that is not series, parallel, or series-parallel - a Wheatstone Bridge is an example of a complex circuit.The techniques for solving series, parallel, and series-parallel circuits cannot be used for solving complex circuits. Instead, network theorems, such as Thevenin's and Norton's Theorems must be used.


What are two features of the Ibanez RG350DX electric guitar?

The two most dominant features of the Ibanez RG350DX guitar is its locking nuts and great quality whammy bar. It also has the ultimate sound quality and is a must buy for guitar lovers.


Why must electricians be extra careful when calculating power requirements for circuits that will run motors?

The electrical code states that motor feeders have to be rated at 125% of the FLA of the motor. When wiring motor circuits always consider the ambient temperature (for wire de-rate purposes) where the motor is located and the 125% rule before selecting the correct wire size. <<>> Extra care must be taken when calculating power requirements for circuits that will carry electric motors because the current need of an electric motor is larger than calculated from its horsepower rating alone. Electric motors are highly inductive and also have an in-rush current requirement to get started. The circuit used to power an electric motor has to be capable of supplying the in-rush and steady state currents to the motor -- with an acceptable I^2-R loss on the wires.


Does a series circuit always use one battery?

Any circuit may use as many power sources as you wish. For DC circuits you must maintain the same polarity. For AC circuits you must synchronize frequency and match voltages.


What are some types of electric circuits?

Some different types of circuits are:openclosedparallelseriesThere are two types of basic circuits, series and parallel.In series, current stays constant and voltage is divided amongst the resistors.In parallel the voltage stays constant, Every branch of the circuit gets the same voltage from the power supplier, but there is different current in every branch but current doesn't get lost. Current entering a junction(branches) must equal to current out of the junction. Iin =Iout.The third type could be the Series-Parallel Combination, which has some components wired in series and other components in parallel. Solving these circuits requires more complex analysis techniques. See related link.Another AnswerElectrical circuits are generally classified as being: (1) series, (2) parallel, (3) series-parallel, and (4) complex. The term, 'complex' is a category into which any circuit that doesn't fall into the first three categories, is placed.


Is an Eulerian circuit traversable?

Yes. Because Eulerian circuits are a subset of Eulerian trails, all Eulerian circuits must be traversable since, by definition, a Eulerian trail is traversable.