0
The emitter, the base, and the collector are parts of a transistor.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
What are the three element of a transistor?
For a BJT transistor the three basic elements are collector, base and emitter. For a FET transistor are drain, gate and source which are analogous for the BJT parts mentioned before.
What is the significance of dc load line in a transistor?
A load line is used in graphic analysis of circuits, having both linear and non-linear parts, representing the constraint the other parts of the circuit put on the non-linear transistor. It represents the response of the linear circuit connected to the transistor. The DC load line describes the DC operation of a transistor graphically.
What are sleep transistors?
A rest transistor is either a pMOS or nMOS high VT transistor and is utilized as a change to close off force supplies to parts of a configuration in standby mode. The pMOS rest transistor is utilized to switch VDD supply and henceforth is known as a "header switch."
Is active is a cutoff region of transistor?
The active region of a transistor is when the transistor has sufficient base current to turn the transistor on and for a larger current to flow from emitter to collector. This is the region where the transistor is on and fully operating.
Different between power transistor and transistor that used in small signal?
Power transistor can conduct large amount of currents through it, more than small signal transistor. power transistor has a vertical structure and small signal transistor has horizontal structure.In power transistor quasi saturation region is present which is absent in the small signal transistor. In power transistor there is a inculsion of drift layer which is not there in the small signal transistor. Power dissipation is less in power transistor and it is more in small signal transistor. b.v.polytechnic,vasai pushkar vaity.
What is the definition of AND gates?
AND gates are parts of electronic transistor circuitry.
What are the three element of a transistor?
For a BJT transistor the three basic elements are collector, base and emitter. For a FET transistor are drain, gate and source which are analogous for the BJT parts mentioned before.
What are the three element of transistor?
For a BJT transistor the three basic elements are collector, base and emitter. For a FET transistor are drain, gate and source which are analogous for the BJT parts mentioned before.
What is the significance of dc load line in a transistor?
A load line is used in graphic analysis of circuits, having both linear and non-linear parts, representing the constraint the other parts of the circuit put on the non-linear transistor. It represents the response of the linear circuit connected to the transistor. The DC load line describes the DC operation of a transistor graphically.
What are the two differences between a mechanical switch and a transistor?
speedsizeswitch has moving parts, transistor has no moving partsswitch contacts wear out from friction and/or electrical arcs, transistors don'tetc.
What are sleep transistors?
A rest transistor is either a pMOS or nMOS high VT transistor and is utilized as a change to close off force supplies to parts of a configuration in standby mode. The pMOS rest transistor is utilized to switch VDD supply and henceforth is known as a "header switch."
Name four common parts of an electric circuit?
Transistor, resistor, diode, output.
What are the two major differences between a mechanical switch and a transistor?
speedsizeswitch has moving parts, transistor has no moving partsswitch contacts wear out from friction and/or electrical arcs, transistors don'tetc.
What is basic construction of JFET?
A Jfet stands for junction field effect transistor. It is a transistor also known for being the simpleist field effect transistor. The basic construction contains has three parts the P-type input the n-type input and a depletion layer.
What is Si transistor?
A silicon transistor is a transistor made of silicon.
Is active is a cutoff region of transistor?
The active region of a transistor is when the transistor has sufficient base current to turn the transistor on and for a larger current to flow from emitter to collector. This is the region where the transistor is on and fully operating.
What is the purpose of the Unijunction Transistor?
A Unijunction Transistor is a transistor that acts solely as a switch.
