0
opposes changes in current
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
When an inductor and resistor are connected in parallel by how many degrees is the current flow through the resistor out of phase with the current flow through the inductor?
When a resistor and an inductor are both connected to an AC supply, the current in the resistor is in phase with the voltage, while the current in the inductor is a quarter-cycle (90 degrees) behind. Supposing they both draw 1 amp on a 12-volt AC supply. The resistor will dissipate 12 watts, while the inductor will dissipate no power. Any power that enters the inductor comes back to the generator in a later part of the cycle. But the current drawn from the supply is 1.414 amps, so this would be a load with a power factor of 0.707.
Why does an inductor block AC but allow DC?
While it is true that an inductor opposes the flow of an alternating current, it does not necessarily 'block it'. The quantity that opposes the flow of an AC current is the inductor's inductive reactance, expressed in ohms. Inductive reactance is proportional to the frequency of the supply voltage and, at 50 or 60 Hz, the reactance of a transformer's winding is relatively low (although very much higher than its resistance) and, while this acts to limit the amount of current flow, it certainly doesn't act to block that flow.
What happens when a capacitor is connected to a dc supply?
is it ? are you sure ? but i know so many circuit where capacitor is connected with ac supply . still , if u connected a capacitor to dc supply , then : 1. if it is in SERIES with the dc supply , it will block all the dc current as capacitor provides infinite resistance to dc current . application : where u want to block dc current.(simple high pass filter) 2. if it is in PARALLEL with the dc supply , it will not block dc current , but if any ac current comes out from the supply , the ac current will go through the capacitor , as capacitor provides small resistance to ac current. application : a) where u want to block ac current.(simple low pass filter) b) to filter the noise (ac components) of dc supply.
How do you connect a diode across a ac coil?
You mean ac coil, the secondary coil, of a transformer? Then for the purpose of rectification, that is , for changing ac into dc, a diode is connected in series with the secondary coil of the transformer.
What is an ac reactor?
A reactor in an AC circuit is basically an inductor which will filter spikes in source voltage. See the related link.
What is the bahaviorS of the INDUCTOR in ac supply?
Because of Ac supply, current lags voltage by 90 in Inductor.
If an inductor and a switch are connected in parallel through which the current will flow in an AC circuit?
A:The inductor does not allow ac signal to pass through. It blocks ac and passes dc. If the switch is open, then the ac signal wont pass. If the switch is closed, then the ac signal will pass through the switch.AnswerIt is incorrect to say that an inductor 'does not allow' the passage of an alternating current. An a.c. current will pass through an inductor, although the inductor will limit the value of that current due to the inductor's inductive reactance. Inductive reactance, which is expressed in ohms, is directly-proportional to the inductance of the inductor and to the frequency of the supply. The value of the current is determined by dividing the supply voltage by the inductive reactance of the inductor.If the switch is connected in parallel with the inductor, then closing the switch will apply a direct short circuit across the inductor, and the resulting short-circuit current will cause the circuit's protective device (fuse or circuit breaker) to operate.
When an inductor and resistor are connected in parallel by how many degrees is the current flow through the resistor out of phase with the current flow through the inductor?
When a resistor and an inductor are both connected to an AC supply, the current in the resistor is in phase with the voltage, while the current in the inductor is a quarter-cycle (90 degrees) behind. Supposing they both draw 1 amp on a 12-volt AC supply. The resistor will dissipate 12 watts, while the inductor will dissipate no power. Any power that enters the inductor comes back to the generator in a later part of the cycle. But the current drawn from the supply is 1.414 amps, so this would be a load with a power factor of 0.707.
Does inductor allow ac to pass through it?
Yes, with some difficulty. You can think of an inductor as a kind of "AC resistor"in a way. The higher the frequency of the AC, the more difficulty it has passingthrough the inductor.If you apply AC voltage across an inductor, whereV = voltage of the ACf = frequency of the ACL = inductance of the inductor,then the AC current through the inductor isI = V/2 pi f L
Why does the lamp bright when connected to the AC?
why does the lamp bright when it is connected to the AC supply
What type of voltage must be passed across a transformer?
A transformer must be connected to an alternating current (AC) supply of the correct voltage.
Why cant you use the voltage across the inductor and the voltage across the lamp to find the supply voltage in a fluorescent fitting?
Because the two voltages are out of phase, that means that individually they peak at different times in the AC cycle, so in general if they are measured separately their sum will exceed the supply voltage, possibly by up to 41%.
In an AC circuit with only an inductor what will an increase in frequency do?
Inductor impedance is given by jwL, where w=2*pi*frequency. Therefore as the frequency increases the impedance of the inductor increases, causing a larger current flow and a larger power dissipation across the inductor
A series LCR circuit consisting of R10 ohms and impedence 20 ohms is connected across an ac supply of 200 v rms The rms voltage across the capacitor is?
16.32 volts
Can a DC series motor with speed control be connected on AC supply?
A dc series motor with speed control can be connected on ac supply because dc machines are totally reversible.
Why a transformer designed for a 120V AC input will often burn out if connected to a 120V DC source?
All transformers are designed to work on AC. They do not work on DC.If you connect an inductor to DC, the current will increase until the capacity of the source or the conductance (1/resistance) capacity of the inductor and conductors is reached. Often, this condition will overheat and destroy the inductor, or destroy the source. A transformer is not an exception, as it is a form of inductor.
Why does an inductor block AC but allow DC?
While it is true that an inductor opposes the flow of an alternating current, it does not necessarily 'block it'. The quantity that opposes the flow of an AC current is the inductor's inductive reactance, expressed in ohms. Inductive reactance is proportional to the frequency of the supply voltage and, at 50 or 60 Hz, the reactance of a transformer's winding is relatively low (although very much higher than its resistance) and, while this acts to limit the amount of current flow, it certainly doesn't act to block that flow.
