what is load line of transistor what is load line of transistor
A load line is used in graphic analysis of circuits, having both linear and non-linear parts, representing the constraint the other parts of the circuit put on the non-linear transistor. It represents the response of the linear circuit connected to the transistor. The DC load line describes the DC operation of a transistor graphically.
The dc load resistance is Rc but the AC Load resistance is (RcRl). If a load line is drawn the slope of which is -1(Rc Rl) . Then it is called an AC load line and it is to be used when the transistor is operating as an amplifier.
well, this is very simple to understand ,the DC load line of a circuit is nothing but the Kirchoff's voltage law on the out put circuit of the transistor-amplifier. As the KVL is linear equation involving voltage drops the equation of load line is a straight linelet us assume that the transistor is in CE configuration.VCC-VCE-ICRC=0vICRC=VCC-VCE of the form by=aX+c which is in the form of a straight line with positive intercepts on X(VCC) and Y(VCC / RC) axis and a negative slopewhere,x= VCE/RCy= ICm(slope)= -VCC/RC
well the difference mainly exists in the method of finding them , these are :-1. in finding DC load line :-open all AC sourcesopen all the capacitors2. for AC load line:-open all the Dc sourcesshort all the capacitors.
Zener diodes attempt to keep terminal voltage constant. If the load is fairly small, a single zener diode can be used for this purpose. If the load is large enough that the zener cannot hold the voltage within desired margins, I suggest using the zener to control the base of a power transistor; the emitter or collector (depending on transistor type) will be used as the output to the load.
It depends on the total load of the transistor as to what the shape of the slope is for the DC load line. A transistor gains voltage as base current is allowed to flow.
A: A transistor has voltage gain as base current is allow to flow. If the load is constant then a DC mirror azimuth path can be plotted as a function of base current and collector current and that is the load line
A load line is used in graphic analysis of circuits, having both linear and non-linear parts, representing the constraint the other parts of the circuit put on the non-linear transistor. It represents the response of the linear circuit connected to the transistor. The DC load line describes the DC operation of a transistor graphically.
to achieve quiecent operating point
The dc load resistance is Rc but the AC Load resistance is (RcRl). If a load line is drawn the slope of which is -1(Rc Rl) . Then it is called an AC load line and it is to be used when the transistor is operating as an amplifier.
It lies in middle of the DC load line of that Amplifier.
A: Transistor to be effective as an linear amplifier it must be operated in its linear load range. The biasing scheme is to insure that the transistor is put in its linear/load range
The operating point of a device, also known as bias point or quiescent point (or simply Q-point), is the DC voltage and/or current which, when applied to a device, causes it to operate in a certain desired fashion. The term is normally used in connection with devices such as transistors and diodes which are used in amplification or rectification.
well, this is very simple to understand ,the DC load line of a circuit is nothing but the Kirchoff's voltage law on the out put circuit of the transistor-amplifier. As the KVL is linear equation involving voltage drops the equation of load line is a straight linelet us assume that the transistor is in CE configuration.VCC-VCE-ICRC=0vICRC=VCC-VCE of the form by=aX+c which is in the form of a straight line with positive intercepts on X(VCC) and Y(VCC / RC) axis and a negative slopewhere,x= VCE/RCy= ICm(slope)= -VCC/RC
The name is your clue: a transistor and a resistor (the load) are put in series. The output signal is taken from the load resistor. A small input signal (to the third lead of the transistor) will cause the transistor to change resistance ... thus you can get a large output from a small input Amplification.
we should be take two point from the the graph between collector current and emitter-collector voltage.. along the horizontal line collector current is zero and emitter-collector voltage become Vcc,and along the vertical line emitter-collector voltage is zero and collector current become Vcc/RL then by this line that drow between this two point is called load line that in this line the transistor allowed to operate....
A load line is used in graphical analysis of nonlinear electronic circuits, representing the constraint other parts of the circuit place on a non-linear device, like a diode or transistor. It is usually drawn on a graph of the current vs the voltage in the nonlinear device, called the device's characteristic curve. A load line, usually a straight line, represents the response of a linear circuit connected to the nonlinear device in question. The operating point(s) of the circuit are the points where the characteristic curve and the load line intersect; at these points the current and voltage parameters of both parts of the circuit match