The same as in single phase with the same RMS voltage.
Yes, but only for balanced loads (current in all three phases the same value). The voltage value used is the phase to phase voltage.
In India its 415V, 50Hz.
6350.8 volts AC rms. The phase to earth voltage is ( square root(3) ) x lower than the phase-phase voltage on a 3 phase system.
Voltage phase to phase in a 380V 3-phase system refers to the voltage measured between any two of the three live conductors in the system. In a balanced 3-phase system, the phase to phase voltage is equal to the line voltage, which is 380V in this case. This voltage is commonly used in industrial and commercial applications to power heavy machinery and equipment. It is important to note that the phase to phase voltage is higher than the phase to neutral voltage in a 3-phase system.
It is the square root of 3. Multiply 1.732 to 120v. and you get 208. which, on a three phase system, is the voltage from line to ground.
115 is the RMS voltage. The actual voltage is a sine wave from -167 to +167 relative to ground. RMS stands for root-mean-square, and it a way of saying that 155 Volts of DC would do the same work on the same sized load. There can be up to 3 phases, and they are the sine wave, shifted by a part of the curve. In most houses, there are 2 phases, and the voltage to ground for each is 110 to 120 V RMS. The voltage between the 2 is 230-240VRMS. 3 phase gets very complex. Each phase is 115 to ground or neutral. 3 PHASE 115V AC EACH PHASE IS 120 DEGRES PHASE SHIFTED THE EFFECTIVE VALUE IS .639 X 115 THE PEAK VALUE OF PHASE IS 1.41X RMS VALUE.
Yes, but only for balanced loads (current in all three phases the same value). The voltage value used is the phase to phase voltage.
In India its 415V, 50Hz.
There is phase to phase voltage in 3 phase system.AnswerYou don't get voltage 'phase-to-phase'; it's 'line-to-line'!
Average value of the conducting phase voltages
A 3-phase rectifier bridge can be used with a single phase supply, it just means that four of the diodes are not connected. The peak voltage (if a reservoir capacitor is used) is sqrt(2) times the rms supply voltage and the average voltage using inductor smoothing is 0.9 times the rms voltage.
Three-phase voltage in Germany is 400V, single-phase voltage is 230V.
6350.8 volts AC rms. The phase to earth voltage is ( square root(3) ) x lower than the phase-phase voltage on a 3 phase system.
The line-to-neutral (not 'phase-to-neutral'!) voltage on a 400V 3-Phase wye-connected system is 230V.Line voltage is the voltage as measured between any two (2) line conductors (hence its name!). Line voltage is often referred to as the 'line-to-line voltage'.Phase voltage is the voltage as measured between any single line and neutral. Phase voltage is often referred to as a 'line-to-neutral' voltage."400V" on a 400V 3-Phase wye-connected power supply indicates its line voltage. Line voltage in a wye system is always the phase voltage multiplied by the square-root of "3" (1.732) and reflects the vector sum of two individual phase voltages present in a three phase system.Thusly, if the line voltage is "400V", then the phase voltage is 400V divided by the square-root of "3" (1.732), which is 230V.Examples of this for North American power systems are 120/208V, 277/480V and 347/600V. Examples for other areas of the world are 220/380V, 230/400V and 240/415V.
The phase difference between any two live lines is 120 degrees, which allows them to peak in turn in the 360-degree cycle.
The three phase voltage is 380 the hertz is 50
Voltage phase to phase in a 380V 3-phase system refers to the voltage measured between any two of the three live conductors in the system. In a balanced 3-phase system, the phase to phase voltage is equal to the line voltage, which is 380V in this case. This voltage is commonly used in industrial and commercial applications to power heavy machinery and equipment. It is important to note that the phase to phase voltage is higher than the phase to neutral voltage in a 3-phase system.