0
What else can I help you with?
What is the phase current of a three phase 2.2kw 415v motor connected in star?
The line current would be the same if the motor were connected in delta. The current can be based on the rule of thumb which says 7 amps must be allowed for a 1-HP single-phase motor on 240 v. A 2.2 kW motor is three times as powerful, and on a three-phase supply of the same voltage (240/415) it would draw 7 amps.
How many amps does a 30HP motor use hooked to 480v 3 pH 60Hz line?
The electrical code states that a 30 HP induction motor at 460 volts three phase will draw 40 amps. <<>> I = 33.34 AMPS IF EFF.= 95% AND P.F.= 85%
Is amp draw on a 220V motor per leg or combined?
Amp draw is always combined. 220V is uncertain if it is three phase or not, because there are both one phase and three phase applications of the 220V motor. In any case, the answer is always "combined".
How many amps will a 20 KW heat strip draw on 480 volt three phase?
24 amps. This could be three 11.54 resistors connected in star, or three 34.6 ohm resistors connected in delta.
How many amps will a 75KW 525v motor draw?
23
Will a 10 hp 220 volt motor draw large amounts of electricity?
A single phase 10 HP motor will draw aproximately 50 amps. A three phase 10 HP motor will draw aproximately 28 amps.
What is the phase current of a three phase 2.2kw 415v motor connected in star?
The line current would be the same if the motor were connected in delta. The current can be based on the rule of thumb which says 7 amps must be allowed for a 1-HP single-phase motor on 240 v. A 2.2 kW motor is three times as powerful, and on a three-phase supply of the same voltage (240/415) it would draw 7 amps.
What you basically want is will each phase take 26 Amps current for 15HP 3 phase 415VAC motor?
Yes, for a 15HP 3-phase 415V AC motor, each phase will draw approximately 26 Amps of current when running under normal operating conditions. This results in a total current draw of 26 Amps per phase for the motor.
How many amps for 1hp 3phase?
For a 1hp 3-phase motor, the current draw will depend on the voltage supply. Typically, at 230V, a 1hp 3-phase motor will draw around 3.6 amps. However, this value may vary based on the motor efficiency and power factor.
How many amps does a 3 phases 600 volt 10 hp draw?
Assuming the power factor is 1, a 10 hp motor operating at 600 volts in a three-phase system would draw approximately 13.33 amps.
How many amps does a 30HP motor use hooked to 480v 3 pH 60Hz line?
The electrical code states that a 30 HP induction motor at 460 volts three phase will draw 40 amps. <<>> I = 33.34 AMPS IF EFF.= 95% AND P.F.= 85%
How many amps does a 5 hp 208 volt 3 phase motor draw?
read the name plate on the motor
How many amps will a 3 hp motor pull on 230 volts?
It depends on the voltage of the motor, and whether it is single-phase or 3-phase. A 120 VAC 2HP single phase motor draws almost 20 amps, a 240 VAC single-phase 2HP motor draws about 10 amps. A 480 VAC 2HP three-phase motor only draws about 6 amps.
If 5000 watts operates 230 volts three phase what will it draw in amps?
21.739 a 21.739 a
Is amp draw on a 220V motor per leg or combined?
Amp draw is always combined. 220V is uncertain if it is three phase or not, because there are both one phase and three phase applications of the 220V motor. In any case, the answer is always "combined".
Are all large motors three-phase?
Yes, most large motors are three phase. Usually single phase motors only go up to 10 HP. Larger than this and the wire size and contactors used to control the motors becomes extreme. For example a single phase 10 HP motor on 115 volts draws 100 amps. The same single phase motor on 230 volts draws 50 amps. The same 10 HP motor on three phase system draws the following amperage; 230 volts is a 28 amp draw, 460 volts is a 14 amp draw and 575 volts is a 11 amp draw. As you can see the higher the voltage becomes, the smaller the wire feeder size is needed and much smaller size contactor can be used to control the motor.
How many amps does a 1.5 hp 230v 3 phase motor draw?
For a 1.5 hp 230v 3 phase motor, you can calculate the amperage using the formula: Amps = (HP x 746) / (Volts x Efficiency x Power Factor x √3). Assuming an efficiency of 0.85 and a power factor of 0.8, the amperage draw would be approximately 4.3 Amps.
