0
What is the meaning of feeder in electrical distribution systems?
Wiki User
∙ 13y ago
Feeders are conductors which connect the consumers with the sub-station. Tapings to feed current to the consumers are NOT taken from the feeders. Therefore, its current loading remains the same along its entire length. Instead, Tapings to each consumers are taken from the DISTRIBUTORS, whose current loading varies along its length.
Wiki User
∙ 13y ago
Wiki User
∙ 11y agofeeder means from substation up to distribution system having wire called feeder. it is supply feeding system. so this called connecting device.....
Add your answer:
Earn +20 pts
What is difference between feeder and grid?
In an electrical power transmission system: the grid is what the feeder feed into.
What is a ring distribution system?
This is a system whereby the primaries of distribution transformers form a closed loop. The distributors are tapped from different points of feeder througg distribution transformers... Vspyce naani!
What is incomer in electrical panel?
power entering to power panel from the feeder is called incomer powersupply
How you check the stability of the cable feeder?
To make sure that a feeder cable is secure it must be supported. The support distance is stated in the electrical code book. The code also gives support of cable trays, conduit and all the different ways to support cables.
What is a feeder circuit?
Definition from the National Electrical Code Article 100:Feeder. All circuit conductors between the service equipment, the source of a separately derived system, or other power supply and the final branch-circuit overcurrent device.Branch Circuit. The circuit conductors between the final overcurrent device protecting the circuit and the outlet(s).
What is different between feeder breaker and motor breaker?
You have to be careful with terms in the electrical field, Example: Main Feeder Circuits will feed a Transformer for distribution and each of those main circuits might feed numbeous Motor control centers. However each of those circuits could be called a main feeder for the motor control center. Confusing. We have High Voltage Transmittion tansformered down for Distribution. So normally a Feeder Breaker will feed Main circuits that will be used for distribution. Example Your home panel will have a main feeder circuit to the whole panel and distribution breakers to you home.
What is feeder pillar?
feeder pillars are used for distribution of electrical supply to customer in which having a such arrangement that the Incomer with Protection (MCB, SFU,MCCB) from this protection the O/G is connected to the Bus bar and from bus bar the O/G are provided to customer,
What is difference between feeder and grid?
In an electrical power transmission system: the grid is what the feeder feed into.
The primary distribution center provides overcurrent protection and switching control for load feeder circuits used to distribute what type of electrical power?
4160 VAC three phase three-wire delta 50/60HZ electrical power
What is electrical feeder?
Feeders are commonly used to supply power to or from a radio antenna. A feeder can be a pair of parallel wires with closely controlled spacing (twin-wire feeder), or a single wire inside a hollow cylindrical conductor (coaxial feeder. <<>> In Canada the electrical term "feeder" is usually used incorrectly as a substitution for the terms wire or conductor. It is correctly defined is, any portion of an electrical circuit between the service box or other source of supply and the branch circuit over current devices. In the U.S. of A, a feeder definition taken directly from the National Electrical Code: All circuit conductors between the service equipment, the source of a separately derived system, or other power supply source and the final branch-circuit overcurrent device.
Where is a Bus bar in a circuit?
Where there is an electrical connection required from one feeder to many feeder , then you need a reference or grid from where the loads can be distributed.
What is a ring distribution system?
This is a system whereby the primaries of distribution transformers form a closed loop. The distributors are tapped from different points of feeder througg distribution transformers... Vspyce naani!
How many feeder you can use for chiller?
One feeder will do the job. The definition of a feeder in the electrical trade is a set of conductors that supply a source to a load. The sizing of the feeders will depend on what the load current is. The wire count of the feeder will be dependant upon whether the load is single phase or three phase.
What is pillars?
feeder pillars are used for distribution of electrical supply to customer in which having a such arrangement that the Incomer with Protection (MCB, SFU,MCCB) from this protection the O/G is connected to the Bus bar and from bus bar the O/G are provided to customer,
What is incomer in electrical panel?
power entering to power panel from the feeder is called incomer powersupply
What is the meaning of feeder industry?
An industry which provides their finished product to other industries as their base product or raw material are known as " Feeder Industry "
Is the Fujitsu ScanSnap feeder scanner compatible only with Mac systems?
Fujitsu ScanSnap feeder scanner compatible with all systems but compared to other system this Fujitsu scanner has the necessary tools to anchor any Mac-based computing environment.
