answersLogoWhite

0

The white wire in switch model 638313-00 typically connects to the terminal marked "N" or "Neutral." However, it is essential to consult the specific wiring diagram or manual for the device, as configurations can vary. Always ensure power is turned off before working on electrical components to ensure safety.

User Avatar

AnswerBot

2mo ago

What else can I help you with?

Continue Learning about Electrical Engineering

How do you wire a 4way switch?

Connect all white wires together under a wire nut and push them back into the box. Connect all ground wires together and then connect them with a jumper wire to the ground screw on the switch. Connect black power in and power out, if applicable, wires to the bottom screw on the switch. Connect the remaining black wire going to the light to the top screw on the switch.


How do you wire a light to a switch at the end of a run and which controls an outlet?

Bring power into the light switch box 12/2 or 14/2 wire depending on the existing wire. Make sure you use the exactly same size wire that is used on that circuit. If you do not know look at the breaker in the main panel that controls power to that circuit. 20 amp will be 12/2 wire and 15 amp will be 14/2 wire. Now run another wire from the switch box out to the outlet. Inside the switch box, strip both white wires back 3/4" and connect them together under a wire nut and push this back into the box. Connect the 2 ground wires together and then connect that to the ground screw on the switch. You now have 2 black wires left. Connect them to the 2 screws on the light switch. Does not matter which black wire you connect to which screw. At the outlet connect the ground wire to the green ground screw, black wire to copper screw, and white wire to silver screw. That outlet will now be controlled by the light switch.


How do you install a 20 amp switch for well pump?

Black/White/Ground power in and the same out. Tie the incoming and outgoing white wires together under a yellow wire nut and push them back in the box. Tie the ground wires together under a green wire nut and connect the pigtail from those ground wires to the ground screw on the switch. Connect the 2 black wires you have left to the 2 screws on the switch. Doesn't matter which black wire you connect to which screw.


How do you wire multilple power outlets and light?

Power into the first outlet and out to all other outlets, black to gold and white to silver screw, ground wires to ground screw. From the outlet closest to the light switch run power from that outlet up to the switch box. Run another wire from the switch box up to the light. In the switch box tie all the whites together under a wire nut and push them back into the box. Tie all the ground wires together and connect that to the ground screw on the switch. Connect the 2 black wires you have left to the 2 screws on the switch. Does not matter which if you only have power in and power out to the light.


How do you correctly wire a switch to a bathroom fan light combo you have 1 w b g coming from your breaker box you also have 2 w b g wires one that controls the fan and one that controls the light?

Tie all White wires together. Tie the Grounds together and connect them to the ground screw on two switches. Create a pigtail with TWO black wires coming out. Connect a black wire to each of the two switches. (you pick which screw, but be consistent. Connect the black wire from the light to the remaining screw on one of the switches. Connect the black wire from the fan to the remaining screw on the OTHER switch.

Related Questions

How do you wire an outlet switch combo?

To wire an outlet switch combo, first turn off the power to the circuit. Connect the black wire to the brass screw on the switch, the white wire to the silver screw, and the ground wire to the green screw. Then, connect the black wire from the outlet to the brass screw on the switch, the white wire to the silver screw, and the ground wire to the green screw. Finally, connect the remaining black and white wires to the corresponding screws on the outlet. Make sure to secure all connections and test the switch and outlet before turning the power back on.


How to wire a single pole switch?

To wire a single pole switch, first turn off the power to the circuit. Connect the black wire from the power source to the brass screw on the switch. Connect the black wire going to the light fixture to the other brass screw. Finally, connect the white wires together with a wire nut and connect the ground wire to the green screw on the switch. Turn the power back on and test the switch.


How do you wire a 4way switch?

Connect all white wires together under a wire nut and push them back into the box. Connect all ground wires together and then connect them with a jumper wire to the ground screw on the switch. Connect black power in and power out, if applicable, wires to the bottom screw on the switch. Connect the remaining black wire going to the light to the top screw on the switch.


How do you wire in a light switch?

To wire in a light switch, first turn off the power to the circuit. Then, connect the black wire from the power source to the brass screw on the switch, and the black wire from the light fixture to the other brass screw. Connect the white wires together and the ground wires to the green screw on the switch. Finally, secure the switch in place and turn the power back on to test the connection.


What is the correct single pole light switch wiring diagram for installing a new light switch in a residential setting?

To install a single pole light switch in a residential setting, connect the black wire from the power source to the brass screw terminal on the switch, and connect the black wire from the light fixture to the other brass screw terminal. Connect the white wires together with a wire nut, and connect the ground wire to the green screw terminal on the switch. Make sure to turn off the power before starting the installation.


How can I properly wire a switch outlet combo in my electrical setup?

To properly wire a switch outlet combo in your electrical setup, you will need to follow these steps: Turn off the power to the circuit at the breaker box. Remove the existing switch or outlet from the electrical box. Connect the black wire (hot wire) to the brass screw on the switch. Connect the white wire (neutral wire) to the silver screw on the switch. Connect the ground wire to the green screw on the switch. Connect the black wire to the brass screw on the outlet. Connect the white wire to the silver screw on the outlet. Connect the ground wire to the green screw on the outlet. Carefully tuck the wires back into the electrical box and secure the switch outlet combo in place. Turn the power back on at the breaker box and test the switch outlet combo to ensure it is working properly. It is important to follow all safety precautions and local electrical codes when working with electricity. If you are unsure or uncomfortable with the process, it is recommended to consult a licensed electrician.


How do I properly wire a single pole switch to an outlet?

To properly wire a single pole switch to an outlet, first turn off the power to the circuit. Connect the black wire from the switch to the brass screw on the outlet, and the white wire to the silver screw. Connect the ground wire to the green screw on the outlet. Make sure all connections are secure and then turn the power back on to test the switch and outlet.


How do I install a dimmer switch with 4 wires?

To install a dimmer switch with 4 wires, first turn off the power to the circuit. Connect the ground wire to the green screw on the dimmer switch. Connect the black wire to the black screw, the red wire to the red screw, and the white wire to the silver screw. Secure the wires with wire nuts and mount the dimmer switch into the electrical box. Turn the power back on and test the dimmer switch to ensure it is working properly.


How can I properly wire a switch to an outlet?

To properly wire a switch to an outlet, you will need to first turn off the power to the circuit. Then, connect the black wire from the switch to the brass screw on the outlet and the white wire to the silver screw. Finally, connect the ground wire to the green screw on the outlet. Make sure to secure all connections tightly and safely before turning the power back on.


How do you hook up a light switch?

To hook up a light switch, first turn off the power to the circuit. Then, connect the black wire from the switch to the black wire from the power source, and the white wire to the white wire. Finally, connect the ground wire to the green screw on the switch. Secure the switch in place and turn the power back on to test the connection.


How to wire a light switch properly?

To wire a light switch properly, first turn off the power to the circuit. Then, connect the black wire from the power source to the black wire on the switch. Next, connect the white wire from the power source to the white wire on the switch. Finally, connect the ground wire to the green screw on the switch. Make sure all connections are secure before turning the power back on.


How do I properly wire a light switch in my home?

To properly wire a light switch in your home, first turn off the power to the circuit at the breaker box. Remove the old switch and connect the black wire to the brass screw, the white wire to the silver screw, and the ground wire to the green screw on the new switch. Secure the switch in place and turn the power back on to test the light.