0
When a needle of an analog ohmmeter indicates infinity the resistor being measured is?
Wiki User
∙ 9y ago
Open
Anonymous
Add your answer:
Earn +20 pts
What is the configuration of the ohmmeter?
An ohmmeter is connected in parallel to a resistor. Be sure that there is no power in the circuit when testing.
What the function of tolerance for resistor colour code?
Tolerance indicates how much the measured value of a resistance is different from its theoretical value, and it is calculated using percentages.
Why resistor should disconnected from the circuit when measured the value of resistor?
if not disconnected you will measure the resistance of the circuit in parallel with the resistor.
How do you convert voltmeter to ohmmeter?
First you will need a constant current source. Do NOT connect the voltmeter to the constant current source without the resistor to be measured already connected. Do NOT use a battery, it is a voltage source. Then follow these steps to measure a resistor:connect the voltmeter across the resistor to be measuredconnect the voltmeter-resistor combination across the constant current sourceread the voltmeter and record the voltagedisconnect the voltmeter-resistor combination from the constant current sourcedisconnect the voltmeter from the resistorcalculate the resistance from the measured voltage and current from the source with Ohm's law in this form: R = V ÷ IIts much easier to just use the ohms setting on a multimeter.
What is the circuit diagram on how to convert galvanomeer into ohmeter?
Just connect a resistor and a small battery in series with the galvanometer,change the markings on the meter's scale, and you have an ohmmeter.
How do you connect an ohmmeter?
1) All power off !!! 2) Place leads across the object (resistor) to be measured.
What is the configuration of the ohmmeter?
An ohmmeter is connected in parallel to a resistor. Be sure that there is no power in the circuit when testing.
What is the difference between a series ohmmeter and a shunt ohmmeter?
Basically, your series and shunt ohmmeters differ in circuit configuration. Your series ohmmeter is configured in a way that your "meter" (which has internal resistance) is connected in series to your "measured resistor" and we all know that those TWO resistances will ADD up causing some sort of inaccuracy. While on the other hand, your shunt ohmmeter is configured in a way wherein your "meter" is connected in PARALLEL to your "measured resistor" that will ease-up the inaccuracy but will only measure resistances ranging from 200 Ohms to 400 Ohms (typically and depending on your configuration).
How do you test blower motor resistor on a 1994 Toyota pick-up?
Remove and test with an ohmmeter Explain how to test with an ohmmeter?
Is resistor measured in amps?
No, a resistor isn't measured at all. A resistor has a quality called "resistance" - and that value is measured. Resistance is measured in Ohms.
Is a switch and example of a resistor?
No it is not. A resistor has a known resistance that is less than infinity. A switch has a resistance of either infinity when it is open or low when it is closed
What are two familiar mistakes when using an ohmmeter and a voltmeter?
Voltmeter connect in parallel with the circuit setting on voltmeter highest range first then to lower range. Ohmmeter we need to use the ohmmeter meter setting connect across the resistor
What the function of tolerance for resistor colour code?
Tolerance indicates how much the measured value of a resistance is different from its theoretical value, and it is calculated using percentages.
What is a fixed resistor measured in?
Resistance is measured in ohms.
Why Ohmmeter can't read the resistance value when current flow through resistor?
An ohmmeter is a calibrated circuit that puts current through the resistor to measure its value. If something else is also putting current through the resistor that the meter doesn't know about, the meter calibration is disturbed and a false reading results. It may even damage the meter.
Why resistor should disconnected from the circuit when measured the value of resistor?
if not disconnected you will measure the resistance of the circuit in parallel with the resistor.
How do you convert voltmeter to ohmmeter?
First you will need a constant current source. Do NOT connect the voltmeter to the constant current source without the resistor to be measured already connected. Do NOT use a battery, it is a voltage source. Then follow these steps to measure a resistor:connect the voltmeter across the resistor to be measuredconnect the voltmeter-resistor combination across the constant current sourceread the voltmeter and record the voltagedisconnect the voltmeter-resistor combination from the constant current sourcedisconnect the voltmeter from the resistorcalculate the resistance from the measured voltage and current from the source with Ohm's law in this form: R = V ÷ IIts much easier to just use the ohms setting on a multimeter.
