0
DC coupling on the input/output will always give higher gain because AC coupling involves inserting a capacitor, which adds impedance and augments the signal. AC coupling is sometimes necessary though, for such purposes as eliminating DC offset on the base of a transistor, or eliminating a DC offset in a single supply opamp circuit.
Wiki User
∙ 12y ago
Wiki User
∙ 12y agoTransformer coupling
Add your answer:
Earn +20 pts
What is offset current?
On a differential amplifier while there is some voltage offset there is also current offset which is dependent on the value of the F/B resistance the bigger value the more offset.
Why you use capacitor in transistor amplifier in output?
The capacitor is used to block DC bias from the output, so that only the AC signal is passed. In an audio amplifier, for instance, unwanted DC in the output would cause distortion when fed to a speaker, or could even damage the speaker or amplifier. In the case of interstage capacitors, they block DC so that the output of the first stage does not affect the bias of the second stage.
What is amplifier roll off?
A practical amplifier will contain several components of a "shunt" capacitance inherent in the transistor and physical wiring of the amplifier circuit. As the frequency of the input signal increases, the reactance of these shunt-capacitances will decrease until, at a frequency determined by the value of the shunt-capacitance and the circuit impedance, signal attenuation begins to take place. Thus the shunt capacitances limit the high-frequency response of the amplifier (note that the transistor itself also has inherent limits to it's high frequency amplifying capability). In the case of operational amplifiers, many operational amplifiers are internally compensated by a small capacitor (e.g. about 30pf for a 741). The internal frequency compensation capacitor prevents the operational amplifier from oscillating with resistive feedback.
Is gold used in circuit breakers?
Certainly not in the case of high-voltage circuit breakers. Probably not in low-voltage circuit breakers, as copper is a better conductor and has a higher melting point.
Why do you use encoder in an elevator?
Encoder is usually used to measure the speed of a motor or a conveyor and provide feedback to the control system. In this case, the encoder reads the speed of the elevator and gives feedback to its control system
Does the capacitor coupling gives the higher gain in case of amplifier?
NO. Transformer coupling gives the higher gain in case of amplifer.
Which coupling gives high gain in case of amplifier?
no.transformer coupling gives higher gain
Which coupling gives the higher gain in case of amplifier - a Capacitor coupling b Impedance coupling c Transformer coupling?
transformer coupling
Which coupling give higher gain in case of amplifier?
Transformer coupling
Why you need RC coupled amplifier?
Rc coupled amplifier is used where good frequency response required. in case of multistage amplification system,To prevent resistance of one stage to come in parallel with next stage, it is used. we use capacitor as a coupling element between two consecutive stages.
Is a buffer amplifier equivalent to a a one input And gate or or a one input OR gate?
No. In the general case, a buffer amplifier is an analog device, but an AND or an OR gate is a digital device. Even in the specific case of a digital buffer amplifier, its still not the same because the digital buffer amplifier has more power available in its output circuit, giving it a higher fanout than just an ordinary AND or OR gate.
Why you need operational transconductance amplifier?
Usually output of an amplifier is a voltage ,...but in case of Operational Transconductance Amplifier ,Iout (current ) is the output. This feature, makes it useful for Electronic control of amplifier gain .
How do coupling capacitors effect the frequency response of c e amplifier?
coupling capacitors are generally used to couple the the AC component of voltage to the DC component(biased voltage) of the transistor amplifier . As we know that the capacitor itself has some reactance which is variable with the applied frequency Rc=1/wc where w=frequency in radians = 2*pi*f and f= frequency of circuit. and, V=VC+VIN VC= voltage drop on capacitor VIN= resultant voltage available for the transistor for amplification so as, frequency increases reactance decreases drop on C decreases so, voltage available for transistor increases and now you can analyse yourself for the case if frequency decreases
What is the influence of Cohesion and coupling for maintenance?
Coupling is an important metric. If the module P. is tightly coupled to module Q. then a change to module P. may require a corresponding change to module Q. If this change is made, as required, during integration or postdelivery maintenance, then the resulting product functions correctly; however, progress at that stage is slower then would have been the case had coupling been looser. It has been shown that the stronger (more undesirable) The coupling, the greater the fault proneness. In other words, it is easy to believe that strong coupling can have a deleterious effect on maintainability.
What is offset current?
On a differential amplifier while there is some voltage offset there is also current offset which is dependent on the value of the F/B resistance the bigger value the more offset.
Why do the front wheels grab when turning in a parking space in a jeep grand Cherokee?
Viscuous coupling in the transfer case could be going bad.
Why you do not use capacitor in a transistor as switch?
The capacitor is there to block any dc voltage that might be applied to the input terminal, which could cause damage or upset the biassing if it was allowed through to the base.
