0
Why doesn't my compressor shut off when it reaches it's max psi This is a industrial 5hp Ingersol Rand 240v 3phase typehow do i adjust the dump switch?
The likely problem is the setting of your pressure switch. These models differ and you'll likely have to locate the manual for your switch. The manufacturer and model will usually be listed on the pressure switch case. The dump valve will likely do nothing except cause the air to be released in case of overpressure. It won't cause the compressor to shut off when it should.
What else can I help you with?
How much nitrogen is left in the soil after harvesting a leguminous crop?
It depends on:How much nitrogen was in the soil before the legume was plantedNitrogen-holding capacity of the soil typeHow much nitrogen was washed away by precipitation during the seasonWhich legume crop was grownHow efficient the bacteria nodulation wasThis is why soil testing is so important.
What causes frontal rainfall?
Warm air rises quicklier then cold air. When those two meet, the warmer and lighter air rises OVER the colder and heavier air. If the warm air rises the warm air coolsdown when it's very high, and then the warm air forms clouds. A front is the place where cold and warm air meets. Along fronts in Europe, there are found a lot of rain and clouds most of the time.
What care and control procedures need to be in place for drawings and specifications?
Document control for engineering drawings is comprised of both document attributes and a defined control process.Engineering drawings, including technical documents such as specifications, procedures, will usually have these attributes:Owning organization, which is ultimately responsible for the document content.Document identification through the use of a document numbering systemTitle or descriptionDocument revision or other indication of a specific design iterationAuthor(s), reviewer(s) and/or others who created the informationAnd, of course, the appropriate technical information necessary to fulfill their purposeA document control process consists of a set of procedures for creating and maintaining the attributes of engineering drawings. Engineering drawing management processes include business rules that define:Which engineering drawing types are supported, and the contents and format of each typeHow engineering drawings are identified (e.g., owner, number, revision, title)Who is responsible for creating, reviewing and approving engineering drawingsWhen engineering drawings may be released to interested partiesThe conditions under which existing engineering drawings are revised, replaced or canceledHow obsolete engineering drawings are controlled, recalled or destroyedEngineering drawings that reflect a consistent set of attributes, and are controlled using a documented set of procedures, significantly reduce product costs by simplifying design, sourcing, production, customer adoption and field service. PDXpert PLM software offers these precise advantages.
What care and control procedures need to be in place for drawings and specification?
Document control for engineering drawings is comprised of both document attributes and a defined control process.Engineering drawings, including technical documents such as specifications, procedures, will usually have these attributes:Owning organization, which is ultimately responsible for the document content.Document identification through the use of a document numbering systemTitle or descriptionDocument revision or other indication of a specific design iterationAuthor(s), reviewer(s) and/or others who created the informationAnd, of course, the appropriate technical information necessary to fulfill their purposeA document control process consists of a set of procedures for creating and maintaining the attributes of engineering drawings. Engineering drawing management processes include business rules that define:Which engineering drawing types are supported, and the contents and format of each typeHow engineering drawings are identified (e.g., owner, number, revision, title)Who is responsible for creating, reviewing and approving engineering drawingsWhen engineering drawings may be released to interested partiesThe conditions under which existing engineering drawings are revised, replaced or canceledHow obsolete engineering drawings are controlled, recalled or destroyedEngineering drawings that reflect a consistent set of attributes, and are controlled using a documented set of procedures, significantly reduce product costs by simplifying design, sourcing, production, customer adoption and field service. PDXpert PLM software offers these precise advantages.
Rules and regulations in food laboratory?
What are the current guidelines?most people should be eating:· plenty of fruit and veg· plenty of starchy foods such as rice, bread, pasta (try to choose wholegrain varieties when you can) and potatoes· some protein-rich foods such as meat, fish, eggs and pulses· some milk and dairy foods· just a small amount of foods high in fat, salt and sugarIt's also important to eat a variety of foods to make sure we get all the nutrients our bodies need.Food typeHow does it help?Where do we get it?CarbohydratesProvides quick energy. 60% of our diet should comprise 'carbs'.Pasta, cereals and potatoesFatsNB Unsaturated fats are healthy. Too much saturated fat from animal products can lead to heart disease.Provides slow energy. 25% of our diet should be fat.Oils, dairy products, nuts and fishProteinBuilds and repairs muscle. We only need 15% of our diet to be protein.Meat, pulses and fishVitaminse.g. A - for vision, B - for energy production and stress reduction, C - to keep skin healthy, D - to help bones and teethHelps the body work. Helps concentration.Fresh fruit and vegetablesMineralsE.g. Calcium - to strengthen bones, Iodine - for energy production, Iron - prevents fatigueHelps release energy from food. Helps decision makingFruit, vegetables and fishFibreCan't be digested. Fills you up and keeps you 'regular'Fresh fruit, vegetables and wholegrain cerealsWaterMaintains fluid levelsThe tap! It's all you need most of the time.
