With the possible exception of a variable reluctance transformer, you should always avoid core saturation of any type of transformer.
When saturated the magnetic characteristics of the core material is radically changed and the coupling coefficients will be very different. Additionally, many Transformers can overheat and be damaged.
impedance matching layer
Common collector amplifier can be used as a voltage buffer and in impedance matching
making impedances identical. when done between supply and load it is done to maximize power transfer. when done on cables and busses it is done to prevent or minimize signal reflections. a low impedance mismatch reflects an inverted signal, a high impedance mismatch reflects an inphase signal.
buffer circuits helpful in overcoming the impedance matching problem.for example if we want to send a signal from one devise to other ,if there is no impedance matching between this two then signal is not transfered.now if we use buffer in between these two devises then the buffer without changing the signal shape or value it simply transffers the signal
A coupling capacitor in substation is used for power line communication purposes. It used after the wave trap. The capacitance ranges from 2200pf to 10,000pf. It offers very low impedance to high frequency carrier signal and allows them to enter the line matching unit and offers a very high impedance path to low frequency signal or wave and blocks it for reaching the line matching unit. In short, it allows only those frequencies needed for communication purposes.
If the line impedance is Z0 and the load is ZL then connect the load using a transformer with N turns ration. N=sqrt(Z0/ZL)
A: there is no formula the gain of the amp is just reduced by the transformer turn ratio minus efficiency or loss. the transformer is for isolation and impedance matching
You'll need to decide *which* one you want. An impedance-matching transformer has a defined primary-to-secondary turns ratio. This *may* give the level match that you want, it may not. Alternately, you can design for a level match, which also *may* give the impedance ratio you want, it may not. It also has a defined turns ratio, but this may not meet an impedance-matching requirement. For impedance matching find the ratio of impedances, take its square root, and use that as the turns ratio: 2400 ohms to 600 ohms has an impedance ratio of 4:1, so its turns ratio will be (sqrt4) = 2:1. To level-shift 1.23 volts (+4 dB) to 300 mV (-10 dB), the ratio is (1.23/0.3) approx 4:1. From the above, you could match 2400 ohms to 600 ohms, but *not* +4 dB to -10 dB with the one transformer.
Impedance matching is setting the input impedance (load) equal to the fixed output impedance (source) to which it is connected, in order to maximize the power transfer.Matching is obtained when Zload = Zsource.In audio and sound engineering we have really no impedance matching. There is only impedance bridging. Zload >> Zsource.Scroll down to related links and look at "Impedance bridging - Wikipedia".
Impedance matching is used in electronics to get an electronic device with an input and output source to work. Impedance matching will give the electronic it's maximum transfer of voltage. An example of this are FM radio receivers.
because it has high input impedance and low output impedance
Two reasons. 1...When impedance of source and destination match, power transfer is maximum. 2...If a long transmission line is involved, the characteristic impedance of the line must match the destination impedance, or reflections will occur on the line.
Impedance matching network perform the passive amplification.
Impedance matching is the electronics design practice of setting the input impedance of an electrical load equal to the fixed output impedance of the signal source to which it is connected. That is done usually in order to maximize the power transfer and to minimize all reflections from the load. Zinput = Zoutput.
An impedance matching device is used to test the resistance, inductive reactant and capacitive reactant in a circuit. If one component did not match the impedance of the conductor, some of the current will be lost by the conductors itself. In conclusion if electricity is lost, the component needs to meet its regular voltage. It consumes more voltage than expected because of the loss. Impedance matching device can actually reduce electrical cost.
impedance matching layer
to reduce reflection loss from the load