answersLogoWhite

0

Yes, cast iron fittings can be used for gas applications, particularly in older installations. They are durable and resistant to corrosion, making them suitable for handling gas. However, modern installations often prefer materials like steel or brass due to weight and ease of installation. Always ensure compliance with local codes and regulations when using any materials for gas piping.

User Avatar

AnswerBot

10h ago

What else can I help you with?

Related Questions

Required IS-8329 IS-9523 IS-12288 related to ductile iron pipe laying and fittings?

I.S.CODES RELATED TO DUCTILE IRON PIPES IS 9523:1980 Ductile Iron fittings for pressure pipes for water, gas and sewageIS 8329:1977 Centrifugally cast (spun) Ductile Iron pressure pipes for water, gas and sewage IS 12288:1987 Code of practice for laying of Ductile Iron pipes Got it ! OK !


Can you use galvanized connections on gas iron pipe?

Most codes do not allow Galvanized piping/fittings on gas piping. I have used galvanized pipe/fittings on exterior gas piping before in the state of Michigan but other states do not allows this. Check with your local code authorities.


What is the best for gas usage brass fitting or black iron fitting?

Brass is normally used for the gas connector to an appliance and for small shut off valves Piping and related fittings black steel is used ABOVE Ground in on piping not exposed to excessive moisture


Can compression fittings be used for gas piping?

It depends on the laws of your state or country. I would say, to be safe, inspect the gas line and install the same type of fittings you find there.


Can you use a glue on the fittings of a gas dryer?

No, proper pipe dope that is approved for gas installations must be used on all threaded fittings. Using substitutes will not guarantee that a tight fit will be made which can lead to gas leaking into the house.


Can you use pressure fittings on three-quarter inch OD steel pipe for natural gas fittings for kitchen stove or do you always have to use threaded?

Not sure what you mean by pressure fittings. Threaded fittings for steel pipe are pressure fittings. Steel pipe with a 3/4" O.D. is known as 1/2" I.P.S. (Iron Pipe Size) pipe.


What is the best frying pan to use with a gas range?

cast iron.....the best! How do you keep eggs from sticking to cast iron?


Can you use victaulic fittings on methane gas?

No, Victaulic fittings are not recommended for use with methane gas due to the potential risk of gas leakage. It is important to use fittings that are specifically designed and approved for use with methane gas to ensure safety and compliance with regulations.


Who made cast iron gas stove model 828-655?

Jordan Mott was the one who invented the cast iron stove it was call a baseburner. The stove had ventilation to burn coal it was made of heavy cast iron.


What is a CGA fitting?

CGA stands for the Compressed Gas Association. A CGA fitting is standardized system for the attachment of a compressed gas cylinder to the required regulator or transfer line. Examples of CGA fittings would be CGA-580 for Non-flamable, Non-oxidizing gasses such as Nitrogen, Argon, or Helium. CGA-590 is used for compressed air and CGA-326 is used for Nitrous Oxide. There are approximately a dozen commonly used CGA-fittings, with others used for special purposes. These welding fittings are typically used for welding applications, but can extend to other application such as medical and other gas uses. The fitting standards are designed to make the gas connections leak tight and also prevent different fittings from being mixed up. For example, flamable gas fittings have a left hand thread fittings. Oxygen and inert gases have right hand thread fittings. Since a left hand thread fittings cannot be threaded onto a right hand fitting, it is impossible to connect the fuel gas to the oxygen and vise versa. It is easy to determine whether the fitting is a left hand or right hand thread. The left hand fittings all have a small cut or slash on the nut of the fitting that denotes the left hand thread.


Can shark bite fittings be used on propane gas?

Shark bite fittings are primarily designed for use with potable water and can also be used with some heating and cooling applications. However, they are not typically approved for use with propane gas or other fuels. For propane applications, it's essential to use fittings specifically rated and tested for gas use to ensure safety and compliance with local codes. Always consult manufacturer guidelines and local regulations before making installations involving gas.


Do flanged gas fittings need thread tape?

No.