answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

Will a 500volt 50hz squirrel cage motor run on 380volts 50hz?

No, the voltage of 500 volts is too high to operate a 380 volt motor.


What is the Phase resistance of 500 voltage?

Phase resistance refers to the resistance encountered by current in a single phase of a multi-phase system, such as a three-phase electrical system. It is not directly determined by the voltage level, like 500 volts, but rather depends on the characteristics of the load and the conductors in the circuit. To determine the phase resistance, one would typically need to know the current flowing through the phase and the power factor of the load. If you have specific details about the load or system, I can help calculate or explain it further.


How do you run a motor 208 volts ac in a 230 volts suply?

If your motor is rated for only 208 volts you may not be able to use 230 volts for it. It will run, but may shorten the life of the motor. Motors are rated with a 10% tolerance for voltage. This means that a 208 volt motor has a maximum voltage rating of 228.8 volts. So measure you voltage supply and see if it is below 228.8 with a good RMS voltmeter. If it is, you are good to go. If it is not there are two ways to make it work. 1. Put a high wattage ballast resister in series with the supply voltage to drop the voltage to the motor within range of 187.2 to 228.8 volts. To determine the value of the resistor take the Horse Power of the motor and multiply it by 746. This will give the wattage of the resistor, use one at least 20% larger. Next take the Rated Load Amps (RLA) or Full Load Amps (FLA) of the motor and divide it into the difference between 230 (voltage supply) and the 208 (rated motor voltage), this will get you close to the resistance value of the Ballast resistor you need to use. So a 1/2 HP motor with a 1.2 RLA will require about a 18 ohm, 500 watt ballast resistor. This is not the recommended method, but will work. 2. Install a Buck & Boost transformer rate for the HP of the motor that will Buck the supply voltage for the motor down to 208 volts. This is the recommended way and the only way it should be done. Any good commercial electrical supply house can help you properly size the transformer that you will need.


What is EHV?

EHV - EXTRA HIGH VOLTAGE - STARTING 500 KILOVOLTS IN UP (500,000 VOLTS)


What is the difference between a 47uf 50 v capacitor and a 47uf 25v capacitor for a tattoo machine?

A: It may tattoo your face when it blow up if the 25 volts is used where a 50 volts should be, you may substitute 47 mfd 500 volts for the 50volts cap and the 25 volts cap But you cannot substitute 15 volts for the 25 volts capacitor

Related Questions

What size of breaker is use for 75 horsepower 220 volts 3 phase induction motor?

500 amp breaker with 250 mcm cu conductors, NEC list this motor as drawing 192 amps X 250% = 480amps go to the next standard size of breaker which would be a 500.


How many amps drawn a 110KW motor?

Watts = Volts times Amps. Therefore, if the voltage was 220 volts, the motor would draw 500 amps. If the voltage was 4,000 volts, the motor would draw 27.5 amps. The voltages for large powerful motors tend to be relatively high, for example in the 380 Volts to 11,500 Volts range.


Will a 500volt 50hz squirrel cage motor run on 380volts 50hz?

No, the voltage of 500 volts is too high to operate a 380 volt motor.


What is the full load amperage of a 500 HP motor at 4160 volts?

20.833 amps at 240volts equals 5000 watts. Wattage is volts times amps.


How many amps will a 500kw using 240 volts produce?

500,000 watts/240 volts = 2,083.34 Amps (single phase)


What is the power of a motor that draws 500 milliamps using 4 volts?

When 500 mA of current is flowing from a 4-volt supply, the supply is delivering 2 watts of electrical power. We can't tell how much of that power is actually available from the motor in the form of mechanical power, and how much of it is only heating up the parts of the motor.


What is ringing voltage?

It´s 500 volts.


How many amps if you have 500 watts at 250 volts?

The formula you need to use is I = W/E. Use this, easier for the average person: The conversion of Amps to Watts is governed by the equation Watts = Amps x Volts. For example 1 amp * 110 volts = 110 watts 500w = 250v X A amps Therefore: 500w/250v= 2amps


5 amp and 100 volts is what wattage?

The wattage would be 500 watts. This is calculated by multiplying the amperage (5 amps) by the voltage (100 volts), resulting in 500 watts of power.


120 volts plus 500 watts equals how many amps?

The formula you are looking for is I = W/E. Amps = Watts/Volts.


How do you convert a 3 phase car lift to single phase?

The best way is usually to buy a new single-phase motor and replace the 3-phase motor. You can also buy something called a rotary phase converter, but for any amount of HP they are about as expensive as a new motor. Expect to pay 500 to 700 dollars US for a 10hp rotary converter. Static phase converters are not a good choice for motors that start and stop or reverse often, such as yours.


How much electricity will a 75watt solar panel produce?

500 volts!!