0
Phase resistance refers to the resistance encountered by current in a single phase of a multi-phase system, such as a three-phase electrical system. It is not directly determined by the voltage level, like 500 volts, but rather depends on the characteristics of the load and the conductors in the circuit. To determine the phase resistance, one would typically need to know the current flowing through the phase and the power factor of the load. If you have specific details about the load or system, I can help calculate or explain it further.
What else can I help you with?
What does it mean when voltage and resistance are in phase?
The voltage across a resistance is in phase with the current through the resistance because the resitance in non-reactive, i.e. non-inductive and non-capacitative. In the inductive case, the load resists a change in current. In the capacitative case, the load resists a change in voltage. In the resistive case, the load current follows the voltage with no delay, hence there is no phase differential.
In 3 phase voltage increases and current decreases why?
If the load current descrease, there is less voltage drop caused by the resistance of the wire, so the voltage is higher.
What is the phase shift between voltage and current when an capacitance is connected to the circuit?
The amount of phase shift depends on the resistance that is also present in the system. In an ideal situation, the phase shift would be +90 degrees, but that would require a voltage source with zero resistance, conductors with zero resistance, and an ideal capacitor that exhibited only capacitance.
Why do you have voltage to ground but not voltage phase to phase?
There is phase to phase voltage in 3 phase system.AnswerYou don't get voltage 'phase-to-phase'; it's 'line-to-line'!
What voltage would be necessary to produce a current of 3A if the resistance of the curcuit were 50 OHMS?
The voltage is gained by multiplying the current and resistance together, i.e.. 50 x 500 = 25000 Imagine the three as a triangle with the voltage at the top, and the current and resistance at the bottom- V . ---- . I x R The voltage divided by the current is the resistance and the voltage divided by the resistance is the current. Therefore the current times the resistance is equal to the voltage. Having any two of these figures allows you to find the third.
What does it mean when voltage and resistance are in phase?
The voltage across a resistance is in phase with the current through the resistance because the resitance in non-reactive, i.e. non-inductive and non-capacitative. In the inductive case, the load resists a change in current. In the capacitative case, the load resists a change in voltage. In the resistive case, the load current follows the voltage with no delay, hence there is no phase differential.
Which of the following condition exist in a circuit of pure resistance?
in a circuit of pure Resistance (r), IE. voltage source (12 v DC battery) and pure resistance (a light bulb). the voltage (v) and current (i) will be in phase. by adding capacitors and/or inductors to the circuit V and I will be pulled out of phase.
AC circuit that contains both resistance and inductance will have a.The current and voltage in phase b.current will lead the voltage c.current will lag the voltage d.voltage will lag the current?
a. the current and voltage in phase
What is current and voltage waveforms are in phase?
If current and voltage of an AC are in phase, then the "power factor" is 100%, and the load is a pure resistance, with no inductive or capacitive reactance (at least at the operating frequency of the AC).
In 3 phase voltage increases and current decreases why?
If the load current descrease, there is less voltage drop caused by the resistance of the wire, so the voltage is higher.
What is the phase shift between voltage and current when an capacitance is connected to the circuit?
The amount of phase shift depends on the resistance that is also present in the system. In an ideal situation, the phase shift would be +90 degrees, but that would require a voltage source with zero resistance, conductors with zero resistance, and an ideal capacitor that exhibited only capacitance.
When phase and neutral will short means what will be the voltage in neutral?
If the phase and neutral wires are shorted together, the voltage in the neutral wire will be the same as the phase voltage. This is because the short circuit effectively bypasses any impedance or resistance in the circuit, causing the potential difference between the phase and neutral wires to be equal.
Why do you have voltage to ground but not voltage phase to phase?
There is phase to phase voltage in 3 phase system.AnswerYou don't get voltage 'phase-to-phase'; it's 'line-to-line'!
What is phase between voltage and current in a pure inductive circuit?
The phase angle between voltage and current in a purely inductive circuit, under ideal circumstances where there is no resistance at all, is 90 degrees.
What voltage would be necessary to produce a current of 3A if the resistance of the curcuit were 50 OHMS?
The voltage is gained by multiplying the current and resistance together, i.e.. 50 x 500 = 25000 Imagine the three as a triangle with the voltage at the top, and the current and resistance at the bottom- V . ---- . I x R The voltage divided by the current is the resistance and the voltage divided by the resistance is the current. Therefore the current times the resistance is equal to the voltage. Having any two of these figures allows you to find the third.
What will be the resultant voltage if the two phase voltage having no phase difference?
If two phase voltages are the same voltage and the same phase angle, the the resultant voltage will be twice the voltage.
How much voltage is necessary to create a flow of 0.24C in 0.8s through a resistance of 500ohm?
r=500
