answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

How plasma is produced using RF generator?

It's power that is loss during the tuning of the RF network. Ideally the reflective power is tuned to zero before striking the plasma to maximize the efficiency of the RF generator.


Difference between function generator and signal generator?

A signal generator provides a high-fidelity sine wave signal ranging from low frequencies to many GHz. Attenuation, modulation, and sweeping are typical features of a signal generator.A function generator is a lower-frequency instrument that typically provides sine, square, pulse, triangle and ramp waveforms. Function generators provide these standard functions from DC to a few MHz, and provide large voltage ranges.


What is a RF amplifier?

A RF amplifier is a device for electrically amplifying the power of an electrical signal, typically, but not exclusively, radio frequency signals.


Why the received signal in analog communication is distorted by the channel noise than that of digital communication?

If an RF signal is AM modulated with a analogue signal any noise will add or subtract to the amplitude of the RF signal and will be present in the audio signal after detection, also will the noise add itself to the audio signal, where as in digital communication a slight variation in the amplitude of the signal is of no concern because you only work with ones and zeros, it's high or it's low


What are the principles of mixing in electronic communications?

In receivers the received RF signal is mixed with the signal of a local oscillator of a different frequency and the intermediate frequency is then amplified by the IF stages normally 3 that resonate slightly off beat to filter out all harmonics and is then detected by the detector stage where all RF is filtered down to ground and only pure audio is then amplified In receivers the received RF signal is mixed with the signal of a local oscillator of a different frequency and the intermediate frequency is then amplified by the IF stages normally 3 that resonate slightly off beat to filter out all harmonics and is then detected by the detector stage where all RF is filtered down to ground and only pure audio is then amplified

Related Questions

Where can one obtain an RF signal generator?

You can obtain a RF signal generator from a variety of locations. You can try your local electronics store. If they do not stock it you can try places such as Amazon or eBay.


What is working of buffer in rf signal generator?

A; BUFFER is used for isolation, translation of levels and amplification if needed


How would one use a hp signal generator?

Hp signal generator serves as a wireless broadcaster. The engineers designed this instrument. It was designed to be used in RF applications exclusively 50 omega loads.


What are the uses of signal generator or function generator unit two?

A signal generator generates either audio or RF frequencies (depending on the capabilities and designed purpose of the generator) for testing other electronics equipment. Makes it easier to make tests on a device without having to have it "in circuit". It's a lot easier to test a piece of equipment on a work bench rather than trying to test it in place.A function generator supplies TTL (transistor to transistor) square wave pulses, sine and sawtooth wave forms for various testing purposes. It's a lot easier to work on something on the work bench and being able to remove a circuit board and just supply power and a signal saves having to take a whole piece of equipment into the shop. Then again, you also can use an oscilloscope for troubleshooting when you jave a good, known signal to work with. That applies to both types of generators.A: A function generator is just like a signal generator except it generates a function like a ladder step or unusual increases or decreases in voltage to generate a required function


How plasma is produced using RF generator?

It's power that is loss during the tuning of the RF network. Ideally the reflective power is tuned to zero before striking the plasma to maximize the efficiency of the RF generator.


Difference between function generator and signal generator?

A signal generator provides a high-fidelity sine wave signal ranging from low frequencies to many GHz. Attenuation, modulation, and sweeping are typical features of a signal generator.A function generator is a lower-frequency instrument that typically provides sine, square, pulse, triangle and ramp waveforms. Function generators provide these standard functions from DC to a few MHz, and provide large voltage ranges.


The of an antenna depends upon the frequency of the RF signal and the gain?

The size of an antenna depends upon the frequecny of the RF signal and the gain.


What is a rf scale?

A RF scale is a measurement scale used in radio frequency technology to quantify signal strength and power levels. It is typically used to determine the strength of a radio signal in decibels (dB) relative to a reference level. A higher RF scale value indicates a stronger signal, while a lower value indicates a weaker signal.


Is rf signal much more important for capturing or not?

rf is must for modulation and demodulation.


What if rf input and outputs are reversed on a TWT?

If the RF input and output are reversed on a traveling wave tube (TWT), the amplifier will not function correctly. The input signal would not be amplified but instead sent back out through the input port. This would result in no signal being output through the intended output port.


Is an rf power amplifier useful in the home?

The answer to whether an RF power amplifier is useful for your home depends on the qualifty if your equipment. If your T.V. is getting a weak signal for example, an RF power amplifier may be useful to get a better signal.


What occurs whenever a reflected RF signal combines with the main signal?

It produces a high SWR (standing wave ratio) that limits the maximum RF (radio frequency) output.