0
What else can I help you with?
What kind of pipe do you use for hot water line into tub and shower?
always use copper for any kind of water installation
What kind of sealers are useful for copper pipe?
The best sealers for copper pipe are a combination of plumbers tape and plumbers epoxy. The tape is used to temporarily seal any holes while the epoxy dries.
Is there any instrument that can give how much water is flowing in a minute through 1 pipe at normal atmospheric condition?
venturimeter, orificemeter are some of the instruments used to measure the flow rate in pipe.
What is a wrought pipe bend?
wrought pipe bends means straight pipe bend using rotary draw pipe bender. or pipe bend by any method
How many galons of water will flow through a 2 inch pipe at 40 psi?
The flow rate of water through a 2-inch pipe at 40 psi depends on various factors, including the pipe's length, roughness, and any fittings or bends. However, a rough estimate using the Hazen-Williams equation suggests that approximately 1,200 to 1,900 gallons per minute could flow through a 2-inch pipe under those conditions. For a precise calculation, specific details about the pipe system would be necessary.
Cookie cutters can be used on which cookies?
cookie cutters can be used on any kind of cookie........i mean come on people!
What kind of pipe do you use for hot water line into tub and shower?
always use copper for any kind of water installation
How does a cast iron pipe cutter cut the pipe?
Any good plumber knows a diamond blade is the best! ! You can use a Sawzall with "Grit Iron" blades, "Snap Cutters", or "Chain Cutters". Your cheapest way out of it would be either to rent a pair of snap or chain cutters, or buy the grit iron sawzall blades. Depending on how much cast iron your gonna cut, just be prepared to be there for a while if you are making more than 2 cuts through 3 or 4 inch pipe with the grit iron blades. Hi, Just cut a 4" cast iron pipe in less than a minute. I used a diamond blade on a Makita worm drive circular saw. Probably any circular would do as long as it has a little oomph Good Luck !!!! WayneRenovators & Builders Alliance, Inc.wvalzania@renovatorsandbuilders.com When confronted with having to remove a section of 4" diameter cast iron pipe, I initially considered using a hacksaw or grinder but the location was not the greatest(between floor joists under the upstairs bathroom). Save yourself hours of frustration by doing as I did and rent a chain cutter. It required very little clearance around the pipe and cut it perfectly in a few minutes and cost less than $30 cdn. MM SOMETIMES a hacksaw or Sabre saw with metal blades is even better than a snap cutter, as the snap cutter may crush a deteriorated pipe, and not cut it clean. However, with good quality cast, the snap cutters are still the best.
Where is the soffit of a pipe?
The soffit of a pipe refers to the underside or bottom of the pipe. It is the part of the pipe that is facing downwards or towards the ground. The soffit can be important for ventilation and drainage purposes, and it is often covered with a soffit vent to allow air to flow through.
How do you layout any lateral on pipe?
drawing for lateral pipe
What is a wrought pipe bend?
wrought pipe bends means straight pipe bend using rotary draw pipe bender. or pipe bend by any method
What is the volume through a pipe as pressure of a liquid increases?
using an 8mm copper pipe to remove the hydrogen gas from an HHO cell, what is the maximum litres thu put before any back pressure begins in the cell.
What is a stink pipe?
Every building has a "stink pipe." Usually located on the roof these pipes vent air to allow the plumbing drains inside the building to work correctly. As water flows into a plumbing drain pipe, air is vented out of the drain through the "stink pipe." The pipe that goes from the bottom of the back of your toilet, up the side of your house to let any gases produced by the waste escape into the air instead of bubbling back up through your toilet and sticking up your house.
Can sperm with HIV go through blood clot?
If you have ANY kind of unprotected sexual intercourse with someone that has any kind of std or aids you will get infected
Are there any animals that can chew through PVC pipe?
Absolutely! My Black Lab has many times. I realize this might be an answer in relation to a pool problem, but dogs certainly can! Woodchucks are also very destructive. In Calif. Gophers can do this. k
Will hot water line PVC pipe burst if frozen?
yes any pipe will
Are box cutters illegal on planes?
yes any weapon that can harm a other person or kill someone will be illegal.Specially if you hide it.
