Any good plumber knows a diamond blade is the best!
! You can use a Sawzall with "Grit Iron" blades, "Snap Cutters", or "Chain Cutters". Your cheapest way out of it would be either to rent a pair of snap or chain cutters, or buy the grit iron sawzall blades. Depending on how much cast iron your gonna cut, just be prepared to be there for a while if you are making more than 2 cuts through 3 or 4 inch pipe with the grit iron blades.
Hi,
Just cut a 4" cast iron pipe in less than a minute. I used a diamond blade on a Makita worm drive circular saw. Probably any circular would do as long as it has a little oomph
Good Luck !!!!
WayneRenovators & Builders Alliance, Inc.wvalzania@renovatorsandbuilders.com
When confronted with having to remove a section of 4" diameter cast iron pipe, I initially considered using a hacksaw or grinder but the location was not the greatest(between floor joists under the upstairs bathroom).
Save yourself hours of frustration by doing as I did and rent a chain cutter. It required very little clearance around the pipe and cut it perfectly in a few minutes and cost less than $30 cdn.
MM
SOMETIMES a hacksaw or Sabre saw with metal blades is even better than a snap cutter, as the snap cutter may crush a deteriorated pipe, and not cut it clean. However, with good quality cast, the snap cutters are still the best.
To cut a cast iron pipe effectively, use a reciprocating saw with a metal-cutting blade or a snap cutter specifically designed for cast iron. Make sure to wear safety gear, mark the cutting line, and cut slowly and steadily to avoid damaging the pipe.
The best way to cut a cast iron pipe is to use a reciprocating saw with a metal-cutting blade or a snap cutter specifically designed for cutting cast iron. These tools are effective in making clean and precise cuts in cast iron pipes.
yes you can do it but you have to use a cast iron cutter, or cicular saw with a carbon friccion to cut arround the pipe. But if the cast iron pipe in in the ground and it's not muveble,, it may break.. so you have to be carefull and when you finish cutting it you put a piace of ABS pipe 1/2 shorter in each side. In order to incert the hob conectors..
Yes, it should, I actually have a project that needs me to cut a cast iron pipe, and my soulution was to use a plasma cutter. The plasma cutter was develiped to cut both ferrous and non-ferrous materialls. Unlike a oxy-gas torch which is only good for steel which has a high Iron content, Plasma will cut steel, stainless steel (which has a much lower Iron content), Aluminum, and I am sure will cut other metals as well. The cutting action is based more on the extreme concentrated heat cutting the material more than a chemical reaction, or burning action of the material.
To safely and effectively cut a cast iron pipe, you can use a reciprocating saw with a metal-cutting blade or a snap cutter specifically designed for cast iron. Make sure to wear safety gear, such as gloves and goggles, and work in a well-ventilated area. Mark the cutting line on the pipe, secure it in place, and slowly cut through the pipe using the chosen tool. Be cautious of sparks and debris during the cutting process.
A pipe cutter is the best tool to cut PVC pipe.
Use a Barbie head. Sawzall with metal cutting blade to cut through pipe without damaging cast iron pipe.
To effectively cut copper pipe for a plumbing project, use a pipe cutter designed for copper pipes. Measure and mark the pipe where you want to cut it, then place the cutter around the pipe and tighten it. Rotate the cutter around the pipe until it cuts through. Sand the cut edges to remove burrs and ensure a smooth connection.
To cut copper pipe effectively and safely, use a pipe cutter designed for copper pipes. Measure and mark the pipe where you want to cut it, then place the cutter around the pipe and tighten it. Rotate the cutter around the pipe until it cuts through. Wear safety goggles and gloves to protect yourself from sharp edges.
A tube cutter or a pipe cutter is used to cut the pipes or tubes
To effectively use an ABS pipe cutter, start by measuring and marking the pipe where you want to cut. Place the cutter around the pipe, tighten it, and rotate it around the pipe until it cuts through. Make sure to apply consistent pressure and rotate the cutter smoothly for a clean cut.
This takes a while, but should work. Use a hacksaw blade on the inside of the pipe and cut just through the pipe in two or three places depending on the size of the pipe. Once it is cut, you can pry the pieces out of the cast iron body.