0
Can you step up 208 volt to 380-440 volts is it cheaper to have the washer converted or use a step up transformer?
You didn't mention whether the voltages are single phase or three phase or whether it is a commercial machine or one used in the home. I am assuming that you are asking about a single phase washer. That being said yes, 208 volts can be stepped up to 440 volts. To have the washer converted would mean finding a 440 single phase motor with the identical frame type that would fit the same configuration that the 208 volt single phase motor now resides in. The control voltage for the internal controls would also have to be changed out to the new voltage. The transformer would cost as much as a new machine so that is out of the question. You might want to price out a new 440 volt machine, sell the old 208 machine and the money that you get for the old machine, apply it to the cost of the new machine.
What else can I help you with?
Who invented the pressure washer?
Rehano and Carolyn Harold Were the creators of the pressure washer.
How can you fit an over sized steel rod into a small steel washer?
by heating washer
How does a water tap work?
Essentially it contains a screw (under the handle) driving a round rubber washer onto the incoming pipe. This blocks the supply, but also slowly destroys the washer after a few years. At this point the washer can be easily replaced.
When was the first pressure washer invented?
106654567
What would cause the sink to 'cough' when the washer is running?
IF your toilet sink and washer are on the same waste line, which they probably are, the problem is't a short trap. Actually since your washer, toilet and sink have different traps it shoudn't effect anything. The problem probably comes from the washer being what is called a "sudds producing fixture". The sudds produced by your washer can actually go up either your toilet or sink waste line. By code the waste for your washer should be tied in to the sewer main 6' from where your waste line goes up for your bathroom. The only solution is to redo the piping from the sewer main and move your waste line for the washer. it won't harm anything. The worst thing that could happen is you'll get suds out of the drain in the sink
Replace drive belt on washing mach?
That is a cheaper alternative to buying a new washer.
Is there a company that can fix my GE washer cheaper then GE's price?
Most likely, General Electric will need to repair your washer because they specialize in those washing machines. They made them, so they know how to fix them.
Is this a fair price for a washer and dryer?
A fair price for a used Maytag washer and dryer would be around $250 to $300. It will depend on how old the washer and dryer also. The older the less money you should offer.
How to fix lid switch on kitchen-aide washer?
If you are sure the lid safety switch is at fault do not bother with it, they are cheaper and easier to replace
What is the cost of a maytag washer repair consultation?
As a matter of fact you can usually come out cheaper if you buy a used washer from somebody else. If you still want to repair you might want to check out this site. http://repair2000.com/
Where can I find washer and dryers that go together?
You can pick up a washer dryer combo, as in a machine that can do both jobs in the form of one machine. Depending on price and quality, you're looking at something cheaper if you go for the combo. Plus it saves space!
What energy transformations are in a dish washer?
In a dishwasher, electrical energy is converted into mechanical energy to move water around and clean the dishes. Some of this mechanical energy is then converted into thermal energy by the heating element in the dishwasher to warm the water for more effective cleaning.
Can a clothes washer drain be converted to accommodate a toilet?
Only for a urinalIf the discharge is from a sewerage ejector and many only require a 2" waste and it is properly vented of course and discharing into a soil line
What's the difference between a front load washer and a normal washer?
The difference between a front load washer and regular washer is that a front load washer has a door in front were clothes are loaded and that is also where washer settings are located. The regular washer is usually a top load where clothes are loaded on top of the washer.
What is the correct order of installation for a washer and lock washer?
The correct order of installation for a washer and lock washer is to first place the washer on the bolt or screw, followed by the lock washer. The lock washer helps prevent the nut from loosening due to vibrations or other movements.
What is the recommended order of installation for a lock washer and a flat washer?
The recommended order of installation for a lock washer and a flat washer is to place the flat washer first, followed by the lock washer on top of it. This helps to ensure proper locking and securing of the fastener.
Where do you put the windshield washer?
in the washer bottle
