0
What else can I help you with?
Why High voltage test for cables?
High voltage testing is performed to confirm the integrity of a cable's insulation. It is always carried out after a new cable has been installed and terminated, or whenever a new joint is installed.
Where Tap changer placed in transformers primary side or secondary side?
It's installed on the high-voltage side.
Can 11kv breaker be installed on 6.6kv line?
Yes. But,circuit breaker are usually rated in terms of current they can interrupt,not the voltage.
How is a voltmeter wired in with the load?
An inline volt meter is designed to have the voltage pass through it. The wire has to be cut or otherwise disconnected, and the meter installed between the disconnected ends of the wiring.
In one high voltage electric motor installed in your water works ten thermistors were used why?
because tamrat samarjini is in the initial form
What are voltage stabilizers?
Voltage Stabilizer is also called Automatic Voltage Stabilizer or AC Voltage Stabilizer or Voltage Regulator. Actually an automatic voltage stabilizer is designed to automatically maintain a constant voltage level, with protections of equipment against voltage surges, over voltage, under voltage, smoothing impulsive noise.
What is internal regulator?
A voltage regulator that is installed on the back of the alternator
Will a computer accept ram if it had a different voltage than the factory installed ram cards?
A computer will not accept a new RAM that has a different voltage than the factory installed RAM cards.
What are the different types of camera stabilizers available in the market?
There are three main types of camera stabilizers available in the market: handheld stabilizers, gimbal stabilizers, and steadicam stabilizers. Handheld stabilizers are held by the user and help reduce shake while filming. Gimbal stabilizers use motors to keep the camera steady and level. Steadicam stabilizers are body-mounted systems that provide smooth and stable shots while moving.
How do you stabilize a 220 volt 40 amp supply?
To stabilize a 220 volt 40 amp supply, you can use a voltage stabilizer or regulator specifically designed for handling that level of voltage and current. Make sure the stabilizer is rated for at least 220V and 40A to handle the load effectively. Install the stabilizer properly according to the manufacturer's instructions to ensure it functions correctly and provides stable power output.
Why High voltage test for cables?
High voltage testing is performed to confirm the integrity of a cable's insulation. It is always carried out after a new cable has been installed and terminated, or whenever a new joint is installed.
What is installed in SI engine to obtain high voltage for spark plug?
A coil.
How many sets of stabilizers are equiped on the stinar model 5519-b?
There are four sets of stabilizers and the rear stairs lower down to act as the rear stabilizers.
What is voltage stabilizer and what's it's control system circuit?
Voltage stabilizers are the circuits that are used to filter noise from the source voltage. DC voltage generated from a bridge network or diode network will contains voltage glitches. These glitches may cause serious problems to the operation of digital circuits. So a voltage regulator is used to filter these glitches. voltage stabilizer can be built using a voltage regulator ICs like 7805 for +5V, 7809 for +9V, 7905 for -5V, 7909 for -9V and so on.
How does a circuit diagram of an automatic voltage stabilizer look like?
There are several types of voltage stabilizer. Older stabilizers utilized relays that automatically broke the current flow when voltage rised above specified level - that was done sequentially with a high frequency. The simplest stabilizer is a Zener diode that is put in parallel, reverse-biased. When supply voltage is too high(greater or equal than diode reverse breakdown voltage) it'll sink excess current. The easiest stabilizers to use in electronics are integrated circuits like common 7805(positive 5 V votage stabilizer). You can find a iagram of its inner circuit in 7805 datasheet at: http://www.datasheetcatalog.org/datasheets/400/249955_DS.pdf
Cpvc solvent cement stabilizers?
I want to know what stabilizers shall be used for cpvc solvent cement?
What voltage does a potential relay operate from?
The voltage for a potential relay will depend on the circuit that the relay is installed in. The relay can be made for low voltages (5v) to higher voltages (440.)
