0
What else can I help you with?
How do you fix a pinhole in a steel waterline?
Re pipe in copper or replace the pipe with the hole in it. Chances are all the steel is gone so when you try to take apart the threads, they will just shear off. You might find yourself in a world of hurt. Good luck. You will need it!Depending where the pin hole is one can use a bronze rod and braze the hole . If you know how to weld then welding is the way to goOne does NOT just install copper without know the PH of the water, velocity etc.
How do you fix a copper pipe that burst?
There are many ways to fix a burst pipe, if you are experienced in soldering you could re round the pipe closing the burst portion and solder the cracked section, or simply cut the burst section out and solder in a new piece withe two couplings. For the less experienced I would recommend cutting the pipe and using a shark bite repair fitting, it comes with detailed instructions and is made just for the situation you described
Can you fix a sprinkler pipe with duct tape?
Yes, temporarily. In the long run it's more efficient to get the pipe glue relevant to that pipe,
How too fix condensation on plumbing pipe?
Wrap it with insulation
How can you fix a clogged toilet that runs in the bathtub?
It's not the toilet, there's a blockage in the pipes some where after the drain pipe from the toilet joins up with the drain pipe from the tub.You're going to need to have the pipe snaked.
How can I fix a hole in a copper pipe?
To fix a hole in a copper pipe, you can use a pipe repair clamp or a soldering method. For a temporary fix, you can use epoxy putty or a rubber patch. It is important to turn off the water supply before attempting any repair.
How can I fix a copper pipe?
To fix a copper pipe, you can use a pipe cutter to remove the damaged section, clean the ends of the pipe, and then solder a new piece of copper pipe in place using a propane torch and solder. Be sure to follow proper safety precautions and techniques when working with a torch.
How can I fix a hole in a PVC pipe?
To fix a hole in a PVC pipe, you can use a PVC pipe repair kit or epoxy putty. First, clean and dry the area around the hole. Then, follow the instructions on the repair kit or epoxy putty packaging to apply the material over the hole. Allow it to dry and cure according to the instructions before using the pipe again.
How can I fix a leaking copper pipe without soldering?
You can fix a leaking copper pipe without soldering by using a compression fitting or a push-to-connect fitting. These fittings can be easily installed without the need for soldering equipment.
How do you fix a green corrosive pipe from leaking?
If it's a green corroded pipe then it's old copper. -You can't fix it. Replace all the length of corroded pipe with PEX and a union at each end
How can I fix nail pops in the ceiling?
To fix nail pops in the ceiling, you can drive a new nail next to the popped one and then remove the old nail. Fill the hole with spackle or joint compound, sand it smooth, and repaint the area to match the ceiling.
How can I fix a copper water line?
To fix a copper water line, you can use a pipe cutter to remove the damaged section of the pipe. Then, clean the ends of the pipe and the inside of a copper coupling. Apply flux to the cleaned surfaces, insert the coupling, and solder the joint using a propane torch. Finally, allow the joint to cool and check for leaks.
Why is difficult to fix a blunt nail?
Because they do not have an edge or point that is sharp, they are less accurate and less refined. If you must fix a blunt nail, drill a much smaller hole first
How do you fix clanging pipes in baseboards?
Secure them down with pipe clamps or nail them down with nails and screws
How do you fix or patch a drilled hole in a galvanised pipe?
WeldBrazeTap and plugCut out and install a union
How do you fix a carbon drain pipe hole?
Would depend on the material the piping is made from
How can I fix nail pops in my walls?
To fix nail pops in your walls, you can start by removing the nail and filling the hole with spackle or joint compound. Then, sand the area smooth and repaint if necessary. This will help the wall look smooth and seamless again.
