0
What else can I help you with?
How do you repair rusted out at foundation cast iron drain pipe?
If it is "rusted out" you do not repair it, You do replace it with XHCI
Thread schedule 10 pipe?
Because threading thin wall pipe renders the pressure rating ineffective, as it thins the wall to much to be able to withstand the pressure.
To attach a PVC closet flange to a pipe in a basement floor is it sufficient to glue the flange to the pipe or should it be bolted to the concrete?
I know that it is usually suffcient to just glue it,just make sure your mesurements are on point, but if you must be anal use sheilds and screw. Either or. joe hojas
What a npt valve is in a water tank pressure system?
npt, national pipe thread, is a standard for threads on a screw. I (not a plumber) don't believe "npt valve" makes sense , but probably refers to a valve which has npt threading. Yes, a NPT Valve would be a valve with pipe threads as opposed to a sweat valve which has solder connections. There are several other type of piping connections too.
What kind of simple machine is a wrench and pipe?
It's a screw on thanks!
How do you thread a PVC pipe?
To thread a PVC pipe, you can use a pipe threading tool to create grooves on the end of the pipe. This allows you to screw on fittings or connectors securely.
What does the inside of a rusted out cast iron sewer pipe look like?
Rusted cast iron.
How do you repair rusted out at foundation cast iron drain pipe?
If it is "rusted out" you do not repair it, You do replace it with XHCI
How do you remove muffler rusted to pipe from converter?
Hacksaw
How do you install motorcycle baffles?
Remove the heat shield (if there is one) locate the set screw hole, remove the old baffle (if there is one) insert the new baffle with the screw hole mating up with the pipe hole, add a lil' blue locktite to screw, and screw it into the baffle through the pipe. Re-attach heat shield (if there was one removed). If baffle is a quite one with fiberglass wrapping...leave it on.
How do you install baffle?
Remove the heat shield (if there is one) locate the set screw hole, remove the old baffle (if there is one) insert the new baffle with the screw hole mating up with the pipe hole, add a lil' blue locktite to screw, and screw it into the baffle through the pipe. Re-attach heat shield (if there was one removed). If baffle is a quite one with fiberglass wrapping...leave it on.
Is it o.k. to use carbon steel pipe with brass valves?
There are instances when corrosion occurs at the junction of a carbon steel pipe and a brass valve. This is often the result of a pipe threading failure.
How do you remove the threading from the pipe if it broke off?
There is an internal pipe wrench that goes inside the pipe and expands as you turn it and it turns out the broken piece. You should be able to get the tool at a hardware store.
If you are threading one half inch diameter steel pipe and it is going between two female fittings how much pipe needs to be cut if your center to center distance between the fittings is nine inches?
I'm confused by your use of the term, center to center. I'm guessing you mean from the face of the fitting where the pipe threads in. You can usually screw in about 1/2 inch of pipe into a female fitting, so you would need 10 inches to end up with 9 in between. You can screw this together without a union in between? You can only put pipe together in one direction unless you use a union.
What are the potential risks associated with using a rusted galvanized pipe in a plumbing system?
Using a rusted galvanized pipe in a plumbing system can lead to potential risks such as water contamination, reduced water flow, leaks, and pipe corrosion. This can result in health hazards, damage to the plumbing system, and costly repairs. It is important to address and replace rusted pipes to maintain a safe and efficient plumbing system.
Where is coolant bleeder screw on Pontiac Sunfire?
You should see a horizontal steel pipe just in front of the engine. This pipe has the bleeder screw.
Thread schedule 10 pipe?
Because threading thin wall pipe renders the pressure rating ineffective, as it thins the wall to much to be able to withstand the pressure.
