answersLogoWhite

0

Depends if it is the supply cable you are wiring or a cable to the outgoing side. If it is the supply cable you are connecting, call your electricity supply company. They are the only ones authorised to do that work. <><><> Three phase will be at 415V. So proceed with caution! If you want to install a new branch circuit cable you need to be sure you have a three phase supply with a triple pole breaker. If you don't know what you are doing then don't try it as you can easily damage the equipment or yourself! Call a licensed electrician to advise you and quote for doing the job safely and correctly. <><><>

As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.

Before you do any work yourself,

on electrical circuits, equipment or appliances,

always use a test meter to ensure the circuit is, in fact, de-energized.

IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB

SAFELY AND COMPETENTLY

REFER THIS WORK TO QUALIFIED PROFESSIONALS.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Engineering

What does A three phase load requires a minimum of?

Yes, the minimum is three wires, usually used when the three phases are in balance, with equal currents in all three lines. In conditions when the three phases might be unbalanced, a neutral wire is added, which makes it a 3-phase 4-wire system, and the current in the neutral depends on how out-of-balance the currents in the three lines are.


How should the resistance reading compare in each winding of a three phase motor?

The three windings are made the same to maintain a balance in the motor.


What are the three types of phase on its final phase?

single phase, double phase &amp; three phase


What will happen if apply two phase supply to a three phase transformer?

A three phase transformer is simply three transformers so, supplying one phase to a set of three transformers will result in only one phase output. Any loads connected to that transformer that are expecting three phase power will malfunction, and could fail.AnswerA three-phase transformer is NOT 'three separate single-phase transformers', as suggested in the original answer. It is a single transformer with three primary and secondary phase-windings wound around a common three-limb ('core') or five-limb ('shell') core. If a single-phase supply was applied to one of the three primary windings, then single phase voltages would appear across each of the three secondary windings and the remaining two primary windings. These voltages would not be out of phase with each other.


Can you put one phase of a three phase ditribution board through a contactor so that the other phases stay on?

Yes, but you must have your neutral wire to form a return path for your current.

Related Questions

How do you wiring three phase db board?

you have to ceck all your wire that is mains


How do you wire a three phase hager distribution board?

if you don't know, call an electrician to do it for you?


Would a row of washers with inverter drives connected to single phase panel board cost the same to run as it would set up on three phase panel board?

three phase would be cheaper for running motors are more efficient single phase is only used for small motors and loads where operating economy is not a concern


What happens when a three phase air condition shows E5 on the display board?

if you will experience then you will know


What does A three phase load requires a minimum of?

Yes, the minimum is three wires, usually used when the three phases are in balance, with equal currents in all three lines. In conditions when the three phases might be unbalanced, a neutral wire is added, which makes it a 3-phase 4-wire system, and the current in the neutral depends on how out-of-balance the currents in the three lines are.


How should the resistance reading compare in each winding of a three phase motor?

The three windings are made the same to maintain a balance in the motor.


What is mean by 7segment distribution board?

A distribution board which has 7 segments , one for Main incomer, three as sub incomer for each phase and three for singlephase outgoing is called a 7 segment DB


Why do you balance single phase loads across a 3-phase supply system?

On a Delta 3-phase you connect the single phase loads between pairs of the 3-phases. Warning both sides of these loads will be hot! You may want to use 3 isolation transformers so that the real loads have a neutral line.On Y 3-phase you connect the single phase loads between one of the 3-phases and neutral.In each case to balance the loads, try to put similar loads on each phase (or pair of phases).


Do you need the balance board mat for the Wii balance board?

no, don't need it.


When was Wii Balance Board created?

Wii Balance Board was created in 2007.


What are the three types of phase on its final phase?

single phase, double phase &amp; three phase


What will happen if apply two phase supply to a three phase transformer?

A three phase transformer is simply three transformers so, supplying one phase to a set of three transformers will result in only one phase output. Any loads connected to that transformer that are expecting three phase power will malfunction, and could fail.AnswerA three-phase transformer is NOT 'three separate single-phase transformers', as suggested in the original answer. It is a single transformer with three primary and secondary phase-windings wound around a common three-limb ('core') or five-limb ('shell') core. If a single-phase supply was applied to one of the three primary windings, then single phase voltages would appear across each of the three secondary windings and the remaining two primary windings. These voltages would not be out of phase with each other.