answersLogoWhite

0

if you don't know, call an electrician to do it for you?

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

What is mean by 7segment distribution board?

A distribution board which has 7 segments , one for Main incomer, three as sub incomer for each phase and three for singlephase outgoing is called a 7 segment DB


Where are three phase transformer systems used?

Any where that a three phase supply distribution is needed to operate three phase equipment.


What are the applications of three phase to single phase electric power distribution systems?

All high-voltage distribution systems are three-phase. Single-phase 'spurs' off the main line, supplying, for example, farm houses, are simply two lines of a three-phase system.


How do you connect two single phase watt-hour meters to measure three phase lines?

Two single phase meters are not needed. A three phase meter is manufactured and is used when installing a three phase electrical distribution.


Where is Mandy Hager daughter of Jon Hager?

she has three daughters now.


Can a single phase supply be used in a three phase supply?

No, a single-phase supply cannot be directly used in a three-phase system. The voltages and phases are different, so additional equipment such as a phase converter or transformer would be needed to convert the single-phase supply to match the requirements of the three-phase system.


Can you use MCCB instead of fuse in a three phase connection?

Yes, three phase CDP (Central Distribution Panels) all use breakers to distribute the three phase supply voltage to their respective loads.


How do you wiring three phase db board?

you have to ceck all your wire that is mains


How do you connect neutral wire in a threephase distribution board?

In a three-phase distribution board, the neutral wire is typically connected to a neutral bus bar, which serves as a common point for all neutral conductors from the three-phase circuits. The neutral bus bar is then bonded to the ground to ensure safety and prevent potential electrical hazards. It is essential to ensure that the neutral connections are secure and that the system is balanced to avoid overloading the neutral wire. Additionally, local electrical codes and regulations should always be followed when making these connections.


Is there a basic difference between a three phase power transformer and a three phase distribution transformer?

The basic difference is the secondary voltages. On a distribution transformer the secondary voltage is very high. This is to overcome line loss for transmission of electricity over long distances. A three phase power transformer is used at the consumers three phase services end to manipulate voltages that consumers need to operate their equipment. The transformer that feeds your house is considered to be a single phase power transformer.


What is phase supply and three phase supply?

I think you mean 'single-phase supply', rather than 'phase supply'. All high-voltage a.c. transmission and distribution systems are three-phase systems. This is because, for a given load, a three-phase system uses less copper than a single-phase system. Three-phase generators produce three 'phase voltages', each displaced, by 120 electrical degrees. These voltages are produced in three windings which are electrically connected in what is called a 'delta' configuration, with each 'corner' of the delta connected to the transmission system by 'line' conductors. Three-phase systems are either 'three-wire' or 'four-wire' systems. Generally, three-phase, three-wire, systems are used for high-voltage transmission and distribution, whereas three-phase, four-wire, systems are typically (but not always) used for low-voltage distribution. Three-wire systems comprise three conductors called 'line conductors'; four-wire systems comprise three 'line conductors' and a 'neutral conductor'. Depending the voltage standards used in the country in which you live, a single-phase supply is obtained either by connecting single-phase load between any two line conductors, or between any one line conductor and the neutral conductor.


Why is the secondary of three phase distribution transformer usually connected in Y?

The secondary of a three-phase distribution transformer is typically connected in a Y (wye) configuration to provide a neutral point, which allows for the safe distribution of single-phase loads alongside three-phase loads. This configuration also facilitates the use of lower voltage levels for residential and commercial applications, improves voltage regulation, and reduces line losses. Additionally, the Y connection helps in balancing the load across the three phases, enhancing system stability and efficiency.