0
To bridge a Carver GA-250 power amplifier, connect the positive terminal of the output from one channel (e.g., the left channel) to the positive terminal of your speaker. Then, connect the negative terminal of the output from the other channel (e.g., the right channel) directly to the speaker's negative terminal. Ensure the amplifier is set to "bridge" mode, if applicable, and check the speaker's impedance to ensure it matches the amplifier's bridged output specifications. Always consult the amplifier's manual for specific instructions and safety precautions.
What else can I help you with?
What is the voltage gain of a transistor amplifier that has an output of 5 rms and an input of 250 mV rms?
The voltage gain (Av) of a transistor amplifier can be calculated using the formula ( Av = \frac{V_{out}}{V_{in}} ). In this case, the output voltage is 5 V rms and the input voltage is 250 mV rms (which is 0.25 V). Therefore, the voltage gain is ( Av = \frac{5}{0.25} = 20 ). This means the amplifier has a voltage gain of 20.
What is function of an integrated circuit TL072?
A: It is a discontinue wide band amplifier 250 mega HZ I believe. Its function is to amplify those frequency with an 50 ohm output impedance
What is the strongest toothpick bridge design?
24.74 pounds using only 100 toothpicks and wood glue
What is the maximum current of 2500kva transformer?
You need to know the Primary and secondary voltages to do the calculation. we only have 100Kva transformers on our salt furnaces as an example: 100000va / 12v = 8333 amps the secondaries , wire, and electrodes are water cooled.
Why does we use 250ohms with power supply for the instrument calibration?
We use the 250 ohms with the power supply because the internal resistance of a DC power supply is insufficient to develop a resistance.
How many watts has the urei 6250?
The Urei 6250 power amplifier has a power output of 250 watts per channel into 8 ohms.
How many watt amplifier will power two 15 inch speakers?
It depends on the power handling capability of the speakers. Generally, a 500-600 watt amplifier would be sufficient to power two 15-inch speakers that have a power handling capacity of around 250-300 watts each. Make sure to match the amplifier's power output with the speakers' power handling to avoid damaging the speakers.
What amplifier power will I need to power dual 12" Rockford Fosgate subwoofers?
A Rockford 250 watt amp would compliment a 12" Subwoofer very nicely.
What fuse number for lighter on 1996 ford e 250?
Fuse # 10 is a 25 amp fuse for the cigarette lighter , power amplifier and rear power outlet in a 1996 Ford E250
What happens when two 250 watts speakers are connected in 75 watts amplifier in parallel?
They will work OK. When a speaker is rated at 250 W that is only a maximum and speakers will work will less audio power. Putting two speakers in parallel will double the total audio power output for a given volume setting.
What is the span of a beam bridge?
250 Feet
What happens when two 250 watts speakers are connected in 75 watts amplifier in parallel connection?
They will work OK. When a speaker is rated at 250 W that is only a maximum and speakers will work will less audio power. Putting two speakers in parallel will double the total audio power output for a given volume setting.
How far is it from basewater to stamford bridge?
about 250 miles
How much 3 to the power of 250?
3 to the power of 250 (3250) is 1.906837481167966e+119
What is 250 to the 4th power?
250^4 is equal to 3,906,250,000.
What is the voltage gain of a transistor amplifier that has an output of 5 rms and an input of 250 mV rms?
The voltage gain (Av) of a transistor amplifier can be calculated using the formula ( Av = \frac{V_{out}}{V_{in}} ). In this case, the output voltage is 5 V rms and the input voltage is 250 mV rms (which is 0.25 V). Therefore, the voltage gain is ( Av = \frac{5}{0.25} = 20 ). This means the amplifier has a voltage gain of 20.
How do i type 250 to the power of 3?
You type it like this: 250^3
