0
What else can I help you with?
How do you calculate capacity of water tube boiler if heating surface is knows?
Please be more specific...
What is benson load in a supercritical boiler?
Benson point at which vertical steam separator run dry because entering water is converted completly to steam.
What is weir type separator?
A weir type separator is a device used to separate liquids based on their density differences, commonly employed in oil and gas industries. It consists of a weir or overflow mechanism that allows lighter liquids, like oil, to rise to the surface while heavier liquids, such as water, settle at the bottom. The design facilitates the separation of these fluids for further processing or disposal. This type of separator is often favored for its simplicity and effectiveness in handling varying flow rates and compositions.
How would you calculate the cubic capacity of the bucket of an excavator?
To calculate the cubic capacity of the bucket of an excavator, measure the internal dimensions of the bucket: length, width, and depth. Use the formula for volume, which is length × width × depth. If the bucket is a more complex shape, you may need to approximate it to a rectangular prism or use water displacement for more accurate results. Finally, convert the volume from cubic inches or centimeters to cubic yards or cubic meters as needed.
What did Archimedes invent that helped bring water from a lower level to a higher level?
He invented the Archimedes Screw, which was first used to pump bilge water out of ships. It is still used today for pumping liquids and granulated solids such as coal and grain. In 1839, a steamship with a screw propeller was launched - the SS Archimedes.
Bilge oil water separator circuit diagram?
circuit of bilge oil water separator
Where you can get a diagram of an oily bilge water separator for engineering mariners?
oil discharge water discharge
Where does water collect in a ship?
the bilge
What is the water that collects in the bottom of a boat called?
bilge bilge
What is a bilge pump on a boat?
A "bilge pump" is not automatically on a boat. Every boat does however have a bilge area. It is the area in a boat's hull where water collects. This area is seriously recommended to have a "bilge pump" in it on every boat to pump the water out of this area while on the water. Bilge's have drain plugs on the back of the boat for when you take it out of the water to fully drain it.
What type of maintenance should one perform with regards to the bilge of a ship?
A bilge is a part of a ship. A bilge is the lowest compartment on a ship where water tends to collect as it is below the waterline. Bilge maintenance revolves around removing the water that collects in the bilge. This can be done by using buckets and pumps.
Why do all boat have bilge water?
All boats have bilge water due to the natural accumulation of water that seeps into the hull from rain, waves, or leaks. The bilge is the lowest part of the boat's interior, designed to collect this water, which can also include water from cleaning or spills. Regularly removing bilge water is essential to maintain the boat's stability and prevent issues like mold or corrosion. Proper bilge pumps are often installed to facilitate this process.
What is a bilge pump?
A bilge pump is a small pump fitted in ships to pump the bilges clear of water.
What a bilge pump?
A bilge pump is a small pump fitted in ships to pump the bilges clear of water.
What is the difference between water separator and moisture separator?
A water separator is used to remove bulk water from a gas stream, while a moisture separator is used to remove fine water droplets or mist from a gas stream. Water separators are typically used in larger industrial applications, while moisture separators are used in processes where precise control of moisture content is important, such as in compressed air systems.
What is the water in the bottom of the boat called?
IN larger boats, the area at the very bottom of the boat is called the "bilge", and the water there is sometimes called "bilge water". To get rid of it, sailors use bilge pumps to pump the water over the side and out of the boat. For smaller boats that don't have bilge pumps, the sailors will "bail" the water out by scooping it up with any suitable container, and dumping it overboard.
How do you stop a marine mercury bilge siphon pump allowing water in to the boat?
If your engine is a sportjet, it probably has a bilge siphon system that connects to the pump. If so, the siphon hose must be "looped" from the pump above the water line, then back down to the bilge. This should prevent water from backwashing through the hose into the bilge.
