0
What else can I help you with?
What type of connection do you need to join gas pipe?
A male and female thread connection if metal pipe. If poly pipe a welded fusion connection.
What insulation should you use for a cold water pipe?
poly venal chloride
Gallons per minute 1 inch poly pipe 50 psi?
20
Can you cut into cast iron soil pipe with plastic soil pipe?
You can put up to a 2 inch pipe into a 4 inch. If you are putting 4 inch to 4 inch, either take out a section of the cast and put the PVC in or cut out a section and connect the PVC to the cast with rubber sleeves meant for this. You can use a saddle clamp for the 2 inch. It is a half round piece of PVC with a 2 inch connection in it. It is held on with two U bolts that go around the cast pipe. Put it where you need it and mark the 2 inch hole on the cast. Drill a series of 1/8 inch holes around this circle. when you get them all drilled, you can break out the plug. Try to keep it from falling into the cast pipe. Put the saddle clamp on and connect the PVC pipe as needed. Seal the saddle clamp to the cast pipe with plumbers putty.
What is the maximum pressure of a 1.250 pipe?
depends on the pipe like if its copper its rated at 300 psi 200 degree F pvc is rated at 200 psi schedule 40 if its black poly it would be 200 psi most all pipes have it on the side of the pipe ,pressure and degrees.
What is the full form of PPR pipe?
Poly Propylene Random pipe
Can termites eat poly pipe used in swimming pools?
Termites can and do attack (eat) poly pipe used in pools. Before a homeowner uses poly pipe, it is suggested that they contact the poly pipe manufacturer since studies and the factory specs clearly establish it. I have seen termites repeatedly damage self installed poly pipe on an in ground pool. If poly pipe is used, it is absolutely mandatory that the surrounding soil be be treated for termites.
What is the best way to connect a PVC pipe to a poly pipe using a PVC to poly adapter?
To connect a PVC pipe to a poly pipe using a PVC to poly adapter, the best way is to follow these steps: Cut the PVC pipe and poly pipe to the desired lengths. Clean and prepare the ends of both pipes. Apply primer and cement to the PVC pipe and the adapter. Insert the PVC pipe into one end of the adapter and hold in place for a few seconds. Repeat the process for the poly pipe on the other end of the adapter. Allow the cement to dry and set before using the connected pipes. This method ensures a secure and leak-proof connection between the PVC and poly pipes.
What type of pipe can be used for underground gas line?
Coated Copper Pipe that is approved for underground only.
How can I effectively use a DIY pipe clamp for my woodworking projects?
To effectively use a DIY pipe clamp for woodworking projects, first, measure and cut the pipe to the desired length. Attach the clamp pads to the ends of the pipe using screws or glue. Place the pipe clamp on the workpiece and tighten the clamp by turning the handle. Adjust the pressure as needed to secure the workpiece in place. Make sure the clamp is securely fastened before working on the project.
What are the best practices for using a rubber clamp for pipe installation?
The best practices for using a rubber clamp for pipe installation include ensuring the clamp is the right size for the pipe, placing the clamp at the correct distance from fittings, tightening the clamp securely but not too tight, and regularly checking for any signs of wear or damage.
Can you use a victalic clamp on a Plastic Pipe?
No, you cannot. The plastic pipe will crack creating a damaged and burst pipe. Only metallic type pipes are to be used when using such a clamp.
Colonial New York's weather?
If it is a pipe that is not easily cut out and replaced, you can use a pipe clamp. Wrap the clamp around the pipe and tighten the two bolts to compress it around the pipe. If it is a drain pipe as you say, there is very little pressure on t he line, so the clamp should work fine.
What is hpvc pipe?
hardened poly vinyl chloride
What's the primary function of a pipe clamp?
The purpose if a pipe clamp is to hold it in place. Pipe clamps are typically fastened onto something that is stationary to fulfill its purpose. An example would be a wall for pipe associated with guttering.
What are the key differences between a pipe clamp and a parallel clamp, and how do they impact their respective functionalities in woodworking projects?
A pipe clamp uses a pipe to apply pressure, while a parallel clamp has jaws that move in parallel to each other. The key difference is in how they distribute pressure on the workpiece. Pipe clamps are better for larger projects and irregular shapes, while parallel clamps are more precise and better for flat surfaces.
How do you repair an exhaust pipe clamp on a 98 Pontiac grand am gt?
You can replace an exhaust clamp with a new one.
