0
What else can I help you with?
How dc supply is given to transformer used in push pull amplifiers?
The dc is supplied via a centre-tap on the transformer. This ensures zero dc net flux in the transformer core, which enables a much smaller core to be used.
How do you determine vkp and rct for class x current transformer given example of 8005a 15va class x ct?
RCT is Secondary resistance of Current transformer it depends on Design.
What are causes of voltage drop in transformer?
An ideal transformer (one with no losses, and not a bad approximation for the real thing) has an input power equal to its output power. In simple terms, since power is the product of voltage and current, then for a given value of power, as the voltage goes up, the corresponding current will go down.
What if supply given to 3 phase induction motor without rotor?
It'll behave like a transformer on open circuit with a huge leakage reactance due to the very large air gap resulting from there being not rotor. So it will draw a largish reactive current from the supply.
What is the use of transformer utilisation factor?
It tells us how much is the transformer utilised in a given process. For a rectifier,TUF =(D.c.power delivered to the load)/(power rating of transformer secondary)
What happens if a dc supply is given to a transformer under no load?
when dc supply is given to transformer at primary winding , the output at secondary winding will be zero.Because to induce voltage ,countnie changing flux is required ,that can not be obtained from dc supply...........
What is the minimum load have to go for a new transformer?
All transformers have a power rating given in kVA which determine the maximum load that can be connected to that transformer.
Why open circuit test is done on the transformer with low voltage side shorted?
The supply is given on the high voltage side of transformer because the supply voltage required to circulate rated current through the transformer is usually very small So energy is saved.
How dc supply is given to transformer used in push pull amplifiers?
The dc is supplied via a centre-tap on the transformer. This ensures zero dc net flux in the transformer core, which enables a much smaller core to be used.
What is winding transformer?
A winding is the name given each of the coils wound around the transformer's core. A basic transformer has two windings, termed the primary winding (connected to the supply) and the secondary winding (connected to the load).
How do you determine vkp and rct for class x current transformer given example of 8005a 15va class x ct?
RCT is Secondary resistance of Current transformer it depends on Design.
How does a narcissist behave in court when they owe you money?
If the narcissist regards you as a potential future source of narcissistic supply, he will seek to compromise. If he has given up on you as a source of supply - he will fight you tooth and nail.
What size wire 100 kva transformer?
Wire sizing of a feed conductor is based on the amperage that a device draws. To calculate amperage from KVA a voltage of the supply has to be stated. Without this voltage and whether the transformer is single or three phase an answer can not be given.
what is the total units in the given data total kilowatt hour 200 kWh current transformer ratio A?
To determine the total units from the given data, you would need to know the current transformer ratio (A). The total units can be calculated by dividing the total kilowatt hours (200 kWh) by the transformer ratio. For example, if the transformer ratio is 100:1, the total units would be 200 kWh / 100 = 2,000 units. If you provide the specific transformer ratio, I can give a more precise answer.
What is the efficiency of a transformer?
The "all day" efficiency of a transformer is defined as the ratio of energy out/energy in for a given all day cycle.
What happens when load is given to primary side of a transformer?
The Load will consume part of the power and therefore reduce the current (voltage ) available for the secondary part of the transformerAnswerYou cannot apply a load to the primary of a transformer which, by definition, is the winding connected to the supply voltage. Your question makes no sense.
What are causes of voltage drop in transformer?
An ideal transformer (one with no losses, and not a bad approximation for the real thing) has an input power equal to its output power. In simple terms, since power is the product of voltage and current, then for a given value of power, as the voltage goes up, the corresponding current will go down.
