Most of them are held in place by two pegs on either side of the overflow tube. If there are no pegs, get a flapper with the ring at the hinge point and it slides down over the tube. The old one may be fairly stiff when trying to get it off of the pegs. Twist the tab sidewise and it should come off.
To install a toilet bowl, first, turn off the water supply and drain the existing toilet. Remove the old toilet by unscrewing the bolts and lifting it off the flange. Place a new wax seal on the flange, set the toilet bowl onto the flange, and secure it with bolts. Finally, reconnect the water supply, check for leaks, and ensure the toilet is level.
Have the new valve in hand. Cut the toilet water supply off at the commode, or even at the street meter box.Remove water tube or pipe supply and old flush valve. Install new valve and new supply line if required.
yes, by eating it
I am paraphrasing to be sure I am answering your question... I think you are asking... "How do you prevent a loose toilet seal?" answer: Most seals, for a toilet, are a problem if the floor is not level or the toilet sits on a non level surface. If the toilet moves side to side or front to back then the seal WILL fail! Additionally, if you have removed the toilet you must ALWAYS install a new seal.
1. there should be a weight/float connected to the underside of the flap inside the tank. these can come out occasionally and fall into the tank or the tank drain. look to see if the it has become detached, and if so, just reconnect it to the bottom of the flap. 2. if not, you may need to adjust the length of the chain connected to the flush lever. 3. if the flap closes but leaks, it can easily be replaced
The time it takes to assemble and install a new toilet is about one hour.
To install a new toilet flapper in a toilet tank, first turn off the water supply to the toilet. Flush the toilet to empty the tank. Remove the old flapper by disconnecting it from the flush valve. Install the new flapper by attaching it to the flush valve. Turn the water supply back on and test the new flapper by flushing the toilet.
When you purchase a new toilet seat, it is going to come with the instruction manual as to how to install the seat, when you get it in your home for installation.
The purpose of the toilet flap in a plumbing system is to control the flow of water from the toilet tank into the bowl, allowing for flushing and refilling of the bowl after use.
You need to hire a plumber to properly install a new toilet. There are many issues that may arise if you try to install it yourself. Make sure you know the requirements such as shutting off the water before doing it.
A lot of money.
To install a new toilet flange, first remove the old flange and clean the area. Place the new flange over the drain pipe and secure it with screws. Make sure it is level and properly aligned. Finally, connect the toilet to the flange and secure it in place.
Toilet T-issue Toilet Paper Direction Poll:http://www.judyreiser.com/poll.php
To properly install a new toilet flange, first remove the old flange and clean the area. Place the new flange over the drain pipe and secure it with screws. Make sure it is level and flush with the floor. Finally, connect the toilet to the flange using a wax ring and bolts, then secure the toilet in place.
To replace a broken toilet flange, you will need to remove the toilet, unscrew the old flange, clean the area, install a new flange, and reattach the toilet. Make sure the new flange is securely in place before reattaching the toilet.
To change a toilet flange, you will need to remove the toilet, unscrew the old flange, clean the area, install a new flange, and then reattach the toilet. It is important to ensure the new flange is securely in place before reattaching the toilet to prevent leaks.
To properly install a pipe toilet in a bathroom, follow these steps: Turn off the water supply to the bathroom. Remove the old toilet and clean the area. Install a new wax ring on the flange. Place the new toilet over the flange and secure it in place with bolts. Connect the water supply line to the toilet tank. Turn on the water supply and check for leaks. Test the toilet by flushing it a few times to ensure it is working properly.