The detailed directions are printed on front of EVERY gas regulator. - However, in general terms, turn regulator switch to OFF for 2 minutes, then to PILOT and depress for one minute, then light pilot or press clicker till it lights. Keep PILOT pressed for 2 more minutes then slowly release it. If it stays on then turn main switch to RUN or ON. -If you have to light the pilot manually, use a barbecue match (12 inches long)
Have you turned the control from Pilot to On? Have you increased the temperature setting?
Most pilot lights are not adjustable. If it's not working properly the usual solution is to change the thermocouple.
Spillage excessive condensate bad thermocouple draft
When pilot light goes out, gas flows out of the pilot light nozzle. If out has continued for a long time, a gas cloud can develop around the furnace. When you go to light the pilot light, you'll ignite this gas cloud and make a big fire ball. If your basement is drafty, you might never get a huge cloud of gas hovering around your furnace. When you notice that your pilot light is out, you should shut off the gas to the furnace and allow any stray gas to dissipate before you turn the gas back on and light the pilot light. alliedallcityinc.com
The thermocouple is usually the first thing to change. It controls the valve and the spark ignition is just to light the pilot.
To determine if the water heater pilot light is out, locate the pilot light access panel on the water heater. Look inside to see if the pilot light is lit. If it is not lit, you may need to relight it following the manufacturer's instructions.
To light a gas heater with an electronic pilot, locate the pilot light button on the heater. Press and hold the button while simultaneously pressing the ignition button. Keep holding the pilot button for about 30 seconds to allow the pilot light to ignite. Release the pilot button and adjust the temperature as needed.
Have you turned the control from Pilot to On? Have you increased the temperature setting?
The heater pilot light may not stay lit due to issues with the thermocouple, gas supply, or a dirty pilot light. It is important to check and clean these components to ensure the pilot light stays lit.
The pilot light on the water heater went out because there was a lack of gas flow or a problem with the ignition system.
If the pilot light is on, the heater should come on by itself. If the pilot light is off then it has to be lit. If it will not stay on, the thermocouple is bad.
To turn on the water heater pilot, locate the pilot light button or knob on the water heater. Turn the knob to the "pilot" setting and hold it down. While holding the knob down, use a long lighter to ignite the pilot light. Once the pilot light is lit, continue holding the knob down for about a minute before releasing it. This should successfully turn on the water heater pilot.
To turn on the pilot light for your water heater, locate the pilot light assembly near the bottom of the water heater. Turn the gas control knob to the "pilot" setting and hold it down. While holding the knob down, use a long lighter to ignite the pilot light. Once the pilot light is lit, continue holding the knob down for about 30 seconds before releasing it. If the pilot light stays lit, turn the gas control knob to the "on" position to start the water heater.
To relight the water heater pilot, locate the pilot light button or knob on the water heater. Turn it to the "pilot" setting and hold it down. While holding the button down, use a long lighter to ignite the pilot light. Keep holding the button for about a minute after the pilot light is lit to ensure it stays on. If the pilot light continues to go out, there may be an issue with the thermocouple that needs to be addressed by a professional.
The gas water heater pilot light may not stay lit due to a faulty thermocouple, a clogged pilot orifice, insufficient gas flow, or a draft near the pilot light.
The water heater pilot light may not stay lit due to issues with the thermocouple, gas supply, or ventilation. These problems can prevent the pilot light from staying lit, leading to the water heater not functioning properly.
The pilot light on your water heater may have gone out due to a variety of reasons, such as a faulty thermocouple, a clogged pilot orifice, a gas supply issue, or a draft in the area where the water heater is located. It is important to troubleshoot and address the specific cause to safely relight the pilot light.