answersLogoWhite

0

you need a tachometer

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Engineering

How can you measure electric motor RPM without a strobe?

Two methods, one uses a dial that is held in the center of the revolving shaft and is directly read off of the dial face. The second method uses a strobe light. The light is focused on the shaft and the dial on the strobe is turned until it looks like the shaft has come to a stand still. The RPM is read off of the meter face of the strobe light.


How check the motor rotation?

To check the motor rotation, first ensure the motor is powered off for safety. Then, manually rotate the motor shaft to feel for any resistance or unusual noises, indicating potential issues. If the motor is powered on, observe the direction of the shaft's rotation, verifying it matches the intended direction specified in the motor's documentation. Additionally, using a tachometer can help measure the RPM and confirm proper operation.


What causes an electric motor to stick when trying to start?

The cam shaft opens the valves for the inlet of gas/air into the piston chamber & exhaust of used fuel has a smooth rpm operating range. The proper timing of the motor to run idle is usually 600-800 rpm. While the motor is trying to start and gain rpm, the pressure from the compression of fuel lags on all other piston until the smooth idle operating rpm is reached. Making the motor lag on start up.


Can a 2800 rpm motor replace a 1400 rpm motor for air compressor?

No


How do you calculate maximum current of 3 phase motor?

By using a simple formulae: f=np/60 where f= frequency, n is the number of pair of poles and 60 is in seconds that motor is turning. So a 4 pole motor with a frequency of 50 hertz will run at 1500 rpm. By manupilating the formulae: n= 50 multiplied by 60 devided by 2 therefore n= 1500rpm. The formula 120xFrequency/poles gives synchronous speed not actual shaft RPM. Induction motors must run at a certain % slip to obtain torque, so a 4 pole motor running at 50hz would be 120x50/4 = 1500 rpm, at 4% slip (operating speed) actual shaft RPM or rated speed would be 1440 RPM.

Related Questions

What calculated speed of a four-pole split-phase motor is 1800 RPM. However if you measure the shaft speed you will find it to be 1725 RPM. What causes this loss of rotational speed?

The loss of rotational speed is due to slip in the motor. Slip is a natural characteristic of induction motors and is necessary for torque production. The difference between the synchronous speed (1800 RPM) and actual shaft speed (1725 RPM) represents the slip in the motor.


How can you measure electric motor RPM without a strobe?

Two methods, one uses a dial that is held in the center of the revolving shaft and is directly read off of the dial face. The second method uses a strobe light. The light is focused on the shaft and the dial on the strobe is turned until it looks like the shaft has come to a stand still. The RPM is read off of the meter face of the strobe light.


What is motor current at zero RPM in vacon nxp ac drive?

Zero rpm at the drive does not exclude the presence of a holding torque on the shaft of the motor due to load in some circumstances. The motor current will be a reflection of the torque presented at the shaft.


If you have motor rpm motor shaft sizeblower pulley size how you get blower rpm?

Drive Pulley = pulley on motor Driven Pulley = pulley on blower First determine your Ratio - divide large pulley size by small pulley size this will give you gear ratio, Example 2" drive pulley and a 4" Driven Pulley = 2:1 gear ratio If you know your motor shaft RPM divide that number by the ratio to get the RPM of the driven pulley, if your shaft rpm is 1800 rpm you would divide 1800 by 2 which would = 900 rpm on your driven pulley if your drive pulley is larger than than your driven pulley you multiply the rpm by the ratio example 1800 rpm x 2 = 3600 rpm


How check the motor rotation?

To check the motor rotation, first ensure the motor is powered off for safety. Then, manually rotate the motor shaft to feel for any resistance or unusual noises, indicating potential issues. If the motor is powered on, observe the direction of the shaft's rotation, verifying it matches the intended direction specified in the motor's documentation. Additionally, using a tachometer can help measure the RPM and confirm proper operation.


What is motor shaft speed?

Motor shaft speed refers to the rotational speed of the motor's output shaft in revolutions per minute (RPM). It indicates how fast the motor is rotating and is a key parameter in determining the mechanical power output of the motor. Motor shaft speed is influenced by the frequency of the electrical power supplied to the motor and the motor's design specifications.


How do you measure RPMs on an electric motor?

There is an instrument that used a strobe light to check shaft rotation on a motor. It is somewhat like the timing light that is used on vehicle engines to check their timing. There is also a mechanical dial device that is physically touched to the pully or gear end and center of the turning rotor shaft and the RPM is read right off of the dial face.


What is the purpose of a laser tachometer?

Laser tachometer are instruments used to measure the rotation speed of a shaft or disk, as in motor or other machine. They usually display the revolutions per minute (RPM) on a calibrated analogue dial or digital display.


Efficiency of motor?

I measure the efficiency of an internal combustian engine by doing (bhp)/((displacement)*(rpm))


How do you measure speed of rotation of a shaft?

The speed of rotation of a shaft can be measured using a tachometer. A tachometer works by measuring the rotational speed of the shaft in revolutions per minute (RPM) or rotations per second. It provides a digital or analog display of the shaft's speed.


What is acceleration in a three phase motor?

It is a measure of how many rpm the motor gains in one second while running up after being switched on.


Why 2900 rpm motor is less price than 1450 rpm motor?

Materials for producing 2900 rpm motor is less than 1450 rpm one