0
If you have an automatic lighter connected to the thermostat follow these directions:
- Turn the on/off/pilot valve to 'pilot'
- Hold the button on top of the controls down completely. This is the thermocoupler button.
- While keeping the thermocoupler button pressed down push the automatic lighter button until the pilot light lites. You can see it lit through the viewing glass.
- Keep holding the thermocoupler button down for a minute after the pilot light is lit.
- If it does not stay lit then your thermocoupler is probably bad and needs to be replaced
What else can I help you with?
What is the risk of an explosion if pilot light on water heater goes out?
When pilot light goes out, gas flows out of the pilot light nozzle. If out has continued for a long time, a gas cloud can develop around the furnace. When you go to light the pilot light, you'll ignite this gas cloud and make a big fire ball. If your basement is drafty, you might never get a huge cloud of gas hovering around your furnace. When you notice that your pilot light is out, you should shut off the gas to the furnace and allow any stray gas to dissipate before you turn the gas back on and light the pilot light. alliedallcityinc.com
Would a pilot light on a gas furnace still work with a defective thermocouple?
Pilot light would work but the main burner would not as the thermocouple proves that there is a pilot light to fire. The main gas valve would not open
Hot water heater pilot light works heater wont light?
Have you turned the control from Pilot to On? Have you increased the temperature setting?
When pilot light goes out on a boiler is gas escaping?
No. The pilot valve is closed when no flame is sensed by the thermocouple.
How do you light the pilot light on a heater?
The detailed directions are printed on front of EVERY gas regulator. - However, in general terms, turn regulator switch to OFF for 2 minutes, then to PILOT and depress for one minute, then light pilot or press clicker till it lights. Keep PILOT pressed for 2 more minutes then slowly release it. If it stays on then turn main switch to RUN or ON. -If you have to light the pilot manually, use a barbecue match (12 inches long)
How do you relight a natural gas pilot light?
How do you relight a natural gas pilot light?
How can I troubleshoot and relight the Honeywell furnace pilot light?
To troubleshoot and relight the Honeywell furnace pilot light, first check for any gas leaks or blockages in the pilot tube. If there are no issues, follow the manufacturer's instructions to relight the pilot light using the reset button or control knob. If the pilot light continues to go out, it may indicate a more serious problem that requires professional assistance.
How do I safely relight the pilot light on a gas stove?
To safely relight the pilot light on a gas stove, first turn off the gas and wait for any lingering gas to dissipate. Locate the pilot light assembly and follow the manufacturer's instructions to relight it using a long lighter or match. If you're unsure or uncomfortable, contact a professional for assistance.
How can I troubleshoot and relight a malfunctioning fireplace pilot light?
To troubleshoot and relight a malfunctioning fireplace pilot light, first check for gas flow and ensure the gas valve is open. Next, follow the manufacturer's instructions to relight the pilot light using a long lighter or match. If the pilot light still won't stay lit, clean the pilot assembly and thermocouple. If the issue persists, it may be a more complex problem requiring professional assistance.
Is it safe to relight the oven pilot light if it has gone out?
Yes, it is generally safe to relight the oven pilot light if it has gone out. However, it is important to follow the manufacturer's instructions and take necessary precautions to ensure safety.
How can I determine if the pilot light is out?
To determine if the pilot light is out, check the small flame near the burner. If it is not lit, the pilot light is out. You may need to relight it following the manufacturer's instructions.
How can I relight the water heater pilot?
To relight the water heater pilot, locate the pilot light button or knob on the water heater. Turn it to the "pilot" setting and hold it down. While holding the button down, use a long lighter to ignite the pilot light. Keep holding the button for about a minute after the pilot light is lit to ensure it stays on. If the pilot light continues to go out, there may be an issue with the thermocouple that needs to be addressed by a professional.
What happens if the pilot light goes out on a furnace and how can it be relit?
If the pilot light goes out on a furnace, the furnace will not be able to ignite and produce heat. To relight the pilot light, you can follow the manufacturer's instructions provided in the furnace manual. Typically, this involves turning off the gas supply, waiting for the gas to dissipate, and then using a long lighter or match to relight the pilot light.
What should I do if the pilot light went out on my gas stove?
If the pilot light on your gas stove goes out, follow the manufacturer's instructions to relight it safely. Make sure the area is well-ventilated and free of gas odors before attempting to relight the pilot light. If you are unsure or uncomfortable relighting it yourself, contact a professional for assistance.
How can I relight the pilot light on my Payne furnace?
To relight the pilot light on your Payne furnace, locate the pilot light assembly and follow the manufacturer's instructions for relighting it. This typically involves turning the gas valve to the pilot position, pressing and holding the reset button, and using a long lighter to ignite the pilot flame. Make sure to follow all safety precautions and guidelines provided in the furnace manual.
Why do pilot lights go out and how can they be relit?
Pilot lights can go out due to drafts, dirt, or a malfunctioning thermocouple. To relight a pilot light, turn off the gas, wait a few minutes, then follow the manufacturer's instructions to relight it using a long lighter or match.
How do I relight the pilot light on my Whirlpool oven?
To relight the pilot light on your Whirlpool oven, locate the pilot light assembly near the burner. Turn the gas valve to the "off" position and wait for the gas to dissipate. Then, turn the gas valve to the "pilot" position and press the ignition button to light the pilot. Hold the button for a few seconds to ensure the pilot stays lit. Finally, turn the gas valve back to the "on" position and test the oven to ensure it is working properly.
