0
One should be able turn the variac all the way to one end of its stroke (typically left), so that the brush contacts the windings right where the neutral connection is. If you cannot, perhaps the stops need adjusted, the brush needs re-aligned/replaced, or the windings need cleaned.
What else can I help you with?
If the function range switch is set at 200 vac what will the multimeter read if a measurement is made directly across both terminals of a blown fuse in a 120 vac line?
With the meter on the voltage scale you will read zero volts across the blown fuse. From the bottom terminal of the service switch fuse to ground you will read zero volts and from the top terminal of the service switch fuse to ground you will read 120 volts. The multimeter will read 0
What is a multi ratio transformer?
A multi ratio CT is just that, it's a CT that has multiple secondary taps. An example is a 1200/5, 5 tap CT, which can be set to many ratios between 100/5 and 1200/5.
What is answer set programming?
programming is set and develop for software &what uou want you will get output
What is the output of a XSLT processor?
The output of an XSLT processor is a set of instructions that dictate how to display the XML data.
How do you convert dc to ac current?
The AC current is fed into a rectifier, which is a set of four diodes that force the current at the output to be one direction. A capacitor across the rectifier output is then used to smooth out the voltage to a level higher than the desired DC output (eliminating, for example, the zero-voltage portions of the original AC sine-wave) A voltage regulator then regulates the voltage to a constant level.
What is the expected amplification of a BJT transistor amplifier if the dc supply is set zero volts?
very simple, zero.
What is the expected amplification of a BJT transistor amplifier if the dc supply is set to zero volts?
It is almost equal to zero volts because no device in this universe can amplify the power --output will be in confine to millivolt or less due to applied magnitude of input signal and ambient noise according to principle Energy can't be created nor destroyed it can only be transferred from one form to another form.
What is the procedure for checking alternator output current?
Use a digital volt meter set to the 20 volt DC scale. A good alternator will output 13.5 to 15.5 volts.
How do you control the ground pin in an arduino?
There isn't any "control" of the ground pin - it is just that - the connection to the common ground. If you mean "How can you make a pin on Arduino go to LOW" (which is the same a zero volts of ground), use the pinMode() function to set a pin to OUTPUT and then issue a digitalWrite() command to that pin setting it to LOW
Can you use any ho transformer for a ho train set?
As long as the transformer is capable of 12 Volts DC output, you can use any transformer with HO scale equipment.
Is the set of zero an element of another set of zero?
No, it is not.
When was Zero Set created?
Zero Set was created in 1983.
Is empty set the same as set of zero?
No. Zero is a number, so the "set of zero" contains one element. The empty set, also known as the null set, contains no elements.
The set of output values of a function or relation?
The set of output values of a function or relation is the range
How many watts required to get 230 volts from generator?
There are no watts to generate volts!! There is a relation that is watts = volts * Amps Generators are set up to generate a specific voltage regardless or watts or amps capacity it has.
If the function range switch is set at 200 vac what will the multimeter read if a measurement is made directly across both terminals of a blown fuse in a 120 vac line?
With the meter on the voltage scale you will read zero volts across the blown fuse. From the bottom terminal of the service switch fuse to ground you will read zero volts and from the top terminal of the service switch fuse to ground you will read 120 volts. The multimeter will read 0
You have 480 volts coming into a stepdown transformer that is set for 440 volts incoming power would this cause your output voltage to be higher than 120 volts?
In short, probably. Transformers step power up or down by a multiplicative factor based on the number of turns in the two transformer coils. Therefore, if you put more voltage in you're going to get a proportional increase in the voltage out.
