0
What else can I help you with?
If circuit is bad how can you find out?
If you have power to a circuit (you can tell with a multi meter), and it does not do what it is supposed to it is bad. Make sure the fuse is good. If fuses keep blowing then there is too much current, which is usually indicative of a short. If you see smoke, there's a good chance you're circuit is bad. An electronics book will tell you what to look for if you are trying to troubleshoot a circuit board. Many times the board will need to be replaced as individual components are too small and impossible to get at to change.
How do you know if a capacitor is good or not?
You test it.For electrolytic capacitors, it's sometimes (but not always) obvious simply by looking at it that there is a problem; if the capacitor bulges or is actually ruptured, that's a pretty good indication that it might be bad. However, the only way to know for certain is to check it to see if it has the proper capacitance.For various reasons it's difficult to test the capacitance of a capacitor which is in a circuit; you'll usually need to detach it and test it in isolation. It is possible to check the equivalent series resistance of a capacitor without removing it from the circuit, and in some cases this may be enough (a correct ESR doesn't necessarily mean the capacitor is good, but an incorrect one means that it's bad).
What is a good thing about series circuit?
There's not much good things about a series circuit, but here's one that i know about. A series circuit has more than one power source or output device. It uses a single path to connect all the devices. An advantage of a series circuit is that you can add more power devices, such as more batteries, and increase the force of the output. This will give you more power. P.S. If you wanna see a bad thing about a circuit, then just type, What is a bad thing about a series circuit? in that box thingy. PEACE ADAM K HAPPINESS
What happened if AVR current sensing fails?
If you mean current sensing using an AVR microprocessor then that entirely depends on the circuit design. A good design would detect the failiure and shut down the current, a bad design would allow the current to flow unchecked and potentially destroy the circuit.
How do you test a good and working contactor?
A contactor is tested by using a device called a Multimeter. By setting the multimeter to ohms and rx1 you can clip both prongs to the coil. If the multinmeter moves the contactor is good. If it doesnt move its bad.
How best can one test a capacitor or a transistor in a circuit to determine whether it's good or bad?
A: Using an multimeter someone could certify the loss of voltage at a node. someone could check for dead shorts. but other then that any reading someone gets it tells not how good or how bad the circuit is.
How do you know if the bulbs r bad or if it is an electrical problem or fuse in a 1998 ford epedition xlt?
Use a test light to analyze the circuit. Use a test light to analyze the circuit.
Can you use smokeless tobacco prior to a urine test?
you can but it is bad for you and no good test pee will have a bad color.
How can you determine if a circuit breaker is bad?
To determine if a circuit breaker is bad, you can check for signs such as tripping frequently, not resetting properly, or feeling hot to the touch. You can also test the breaker with a multimeter to see if it is functioning correctly.
Will the module test good after it has cooled off?
It depends on which module you are talking about. But yes, I've had them test good cool and bad hot.
How can I determine if a circuit breaker is bad?
To determine if a circuit breaker is bad, you can visually inspect it for any signs of damage or wear, test it with a multimeter to check for continuity, and reset it to see if it trips again immediately. If the circuit breaker shows signs of damage, does not have continuity, or continues to trip after resetting, it may be faulty and in need of replacement.
If circuit is bad how can you find out?
If you have power to a circuit (you can tell with a multi meter), and it does not do what it is supposed to it is bad. Make sure the fuse is good. If fuses keep blowing then there is too much current, which is usually indicative of a short. If you see smoke, there's a good chance you're circuit is bad. An electronics book will tell you what to look for if you are trying to troubleshoot a circuit board. Many times the board will need to be replaced as individual components are too small and impossible to get at to change.
How do you know if a capacitor is good or not?
You test it.For electrolytic capacitors, it's sometimes (but not always) obvious simply by looking at it that there is a problem; if the capacitor bulges or is actually ruptured, that's a pretty good indication that it might be bad. However, the only way to know for certain is to check it to see if it has the proper capacitance.For various reasons it's difficult to test the capacitance of a capacitor which is in a circuit; you'll usually need to detach it and test it in isolation. It is possible to check the equivalent series resistance of a capacitor without removing it from the circuit, and in some cases this may be enough (a correct ESR doesn't necessarily mean the capacitor is good, but an incorrect one means that it's bad).
You got a 23 on your ACT Is that good or bad?
That is near the average for most people taking the test. So, you are roughly in the middle of the pack, not good but not bad.
What is the highest score you can get on the sri reading test?
i got a 959. is that good or bad?
Is an alt blood test result of 71 bad?
yes it maynot be good
How can you tell if fuel pump relay is bad on 95 gmc safari?
In order to test the fuel pump relay, you must check that the two control circuit terminals on the relay are not connected, using an ohmmeter. You must also test the power circuit terminals on the relay, in the same way.
