0
What else can I help you with?
What are the values so that over all gain is 10 in instrumentation amplifier?
You need a divider that is 10 to 1. You could use 10 megohms in the feedback and 1 megohm in the bottom leg. Since you are probably talking about an operational amplifier, you need this in both legs.
Where to use series shunt amplifier?
A series shunt amplifier is typically used in applications requiring high input impedance and low output impedance, which is ideal for buffering signals. It is commonly found in audio equipment, sensor interfacing, and instrumentation systems where it helps to minimize loading effects on the signal source while providing a stable output for further processing. Additionally, it can be used in feedback loops for gain control in various electronic circuits.
How do I Add an indicator variable in sas?
To add an indicator variable in SAS, you can use the DATA step along with a conditional statement. For example, if you want to create an indicator variable called indicator based on a condition in the dataset, you can use the following code: data new_dataset; set original_dataset; if condition then indicator = 1; else indicator = 0; run; Replace condition with your specific criteria for the indicator. This will create a new dataset with the added indicator variable.
Where can one learn how to use a video distribution amplifier?
One can learn how to use a video distribution amplifier by reading the guides that come with these products. One can also watch video tutorials on YouTube.
What is the use of finding the bandwidth of an amplifier?
A: Any amplifier will have greater band with if operated open loop. It will also be very unstable so negative feedback is implemented for that reason. There is some drawback when feedback the band width of the amplifier decreases, So is important to find out if the amplifier when stable will it have the band width required
What is the use of instrumentation amplifier in ecg circuit?
for better amplification ...by instrumentation amplification we get the output admittance will be more
What is a difference between an operational amplifier and instrumentation amplifier and can you use one opamp to perform a same task as 3 opamp instrumentation amplifier?
An op amp is made from transistors, resistors and capacitors. It is enclosed in a "chip". A basic instrumentation amp is made of 2 op-amps. you can't have a single op-amp perform as good as a instrumentation amp, although it can perfrom the same task. An i-amp has much better CMMR (common-mode rejection) and a higher input impedance.
How do you increase the imput impedance of instrumentation amplifier?
Use a series resistance at the input. A problem could be that the amplification goes down.
What are the values so that over all gain is 10 in instrumentation amplifier?
You need a divider that is 10 to 1. You could use 10 megohms in the feedback and 1 megohm in the bottom leg. Since you are probably talking about an operational amplifier, you need this in both legs.
The use of swamping resistor in differential amplifier?
the use of swamping resisters in amplifier is in order to protect the amplifier from high temperatures
You will have signal degradation unless you use the amplifier.?
You will have signal degradation unless you use the amplifier.
Places where instrumentation is used?
Ride through your local town and look for smoke or steam rising into the air. These places use instrumentation. Every liquid you consume was manufactured or bottled in a facility using instrumentation. Every time you sneeze, use a napkin or wipe your butt, you are using a product manufactured using Instrumentation. Basically instrumentation is used in all manufacturing facilities in some form.
How do you use a diode as temperature sensor?
The voltage across a Silicon Diode junction varies 0.00011 volts per degree Kelvin. Connect the diode to a high gain amplifier and the output of the amplifier to a DVM using an appopriate voltage scale.
Do hot air balloons use instrumentation?
yes they use altimeters and gps's
How to use the Line out in fender performer 650?
In order to use the line out in the Fender Performer 650, you will need an amplifier. Connect the cable from the line out to the amplifier. Make sure that the amplifier is turned on.
Can you run a 500 watt amplifier at low volume on a 140 watt ac converter?
Yes, you can run a 500 watt amplifier at low volume on a 140 watt AC converter. The power consumption of the amplifier will depend on the volume level it is set to. As long as the amplifier is not drawing more power than what the converter can supply, you should be able to use them together safely. Keep an eye on the power indicator on the converter to ensure it's not being overloaded.
If you have a sub woofer do you need an amplifier?
There are two types of subwoofers. 1. Active subwoofers 2. Passive subwoofers An active subwoofer will have a built-in amplifier. A passive subwoofer doesn't have a built-in amplifier which will require the use of an amplifier, the use of a power source.
