0
I haven't kept up with building codes in a number of years, but believe it was 36" minimum landing at bottom or top of stairs. You need to check out the National Building Code to verify. You can Google this information online,
check for a copy at your local library or make a call to your local building department.
<><>
Located a 2009 edition of the IRC-International
Residential Code on Stairways. You still need to verify that this information is current and suggest you contact your local building department.
STAIRWAYS
46. LANDINGS. Section R311 IRC 2009
R311.7.5 Landings for stairways.
There shall be a floor or landing at the top and bottom of each stairway.
Exception:
A floor or landing is not required at the top of an interior flight of stairs, including stairs in an enclosed garage, provided a door does not swing over the stairs. A flight of stairs shall not have a vertical rise larger than 12 feet (3658 mm) between floor levels or landings. The width of each landing shall not be less than the width of the stairway served. Every landing shall have a minimum dimension of 36 inches (914 mm) measured in the direction of travel.
R311.3 Floors and landings at exterior doors.
There shall be a landing or floor on each side of each exterior door. The width of each landing shall not be less than the door served. Every landing shall have a minimum dimension of 36 inches...
What else can I help you with?
Draw the circuit diagram for stair case and passage lights controlled by the timer?
sirs if you could explain me detail about the staircase lighting ckt diagram & explain how does the switch function.
Can you put a stair lift in garages?
Stair lifts are commonly installed in garages. Many garages are built below the grade of the house and require steps to access the living area. If the garage is fully enclosed an interior stair lift model can be used. If the garage is open (no doors) an outdoor unit may be more suitable in humid areas of the country.
How do you do staircase wiring?
A two way switch is required for staircase wiring. A staircase switch will have two terminals. Connect the line wire with the center terminal. Connect the two ends of a wire with the top two terminals and two ends of a wire with the bottom two terminals. The line wire at the center terminal can now be connected with one terminal of the light bulb or light holder.
What is a stair post called?
Newel posts are used at each end of stair balustrading with spindles or balusters along the length supporting the handrail.
Are stairlifts easy to install?
Stair lifts by manufacturers such AmeriGlide are said to be well favored by customers and incredibly easy to install. Electric powered stair lifts are said to be more difficult. However, battery powered stair lifts are easier for installation.
What is the formula for calculating the slope of a staircase, incorporating the measurements of the stair rise and run?
The formula for calculating the slope of a staircase is: slope rise / run. This means you divide the height of the stair rise by the depth of the stair run to determine the slope of the staircase.
How do I go about installing vinyl stair nose on my staircase?
To install vinyl stair nose on your staircase, first measure and cut the stair nose to fit the width of each step. Next, apply adhesive to the back of the stair nose and press it firmly onto the front edge of the step. Use a rubber mallet to ensure a secure bond. Repeat this process for each step until the staircase is complete.
How do you calculate stair stringers for a staircase?
To calculate stair stringers for a staircase, you need to determine the total rise and total run of the staircase. Then, you can use a mathematical formula or an online calculator to find the length and angle of the stair stringers. This will help you cut the stringers accurately to ensure a safe and stable staircase.
How do I properly install laminate stair nose for my staircase?
To properly install laminate stair nose for your staircase, follow these steps: Measure and cut the stair nose to fit the width of the staircase. Apply construction adhesive to the back of the stair nose. Press the stair nose firmly onto the front edge of the stair tread. Secure the stair nose in place with finishing nails or screws. Fill any gaps with wood filler and sand down any rough edges. Finish by painting or staining the stair nose to match the rest of the staircase.
What are the different types of stair trim available for enhancing the appearance of a staircase?
The different types of stair trim available for enhancing the appearance of a staircase include baseboards, stair nosing, cove molding, and quarter round molding.
What is stair case?
A flight of stairs in it's entirety is a staircase
How many stair stringers do I need for my staircase?
The number of stair stringers needed for a staircase depends on the width of the stairs and the building codes in your area. Typically, you will need one stringer for every 16 inches of stair width. It is recommended to consult with a professional to determine the exact number needed for your specific staircase design.
Which companies will help design staircases?
There are companies dedicated to staircases, such as Stair Plan, which will be happy to help. Alternatively, most interior design companies will be perfectly willing to get involved with a staircase project.
What is a stair stringer?
A stair stringer is what holds up the stairs. Usually, a staircase has at least two of these supports to hold it up.
What are stair tread rugs needed for?
Stair tread rugs are used to decorate staircase steps. They can also be used for protecting the floor of a staircase from dirt on someone's shoes or damages to the floor such as a burn or a scratch.
How do you spell stair case?
It is one word "staircase" (open flight of stairs, usually with rails).
What is the best method for installing vinyl floor stair nose on a staircase?
The best method for installing vinyl floor stair nose on a staircase is to measure and cut the stair nose to fit the width of the stairs, apply adhesive to the back of the stair nose, and then press it firmly into place on the edge of the stair tread. Make sure to follow the manufacturer's instructions for the specific adhesive and installation process.
