answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

What are the differences between boilers and burners?

A burner is the part of the boiler that creates and controls the flame that heats the water. If you meant difference between a boiler and a furnace, a boiler makes hot water and a furnace makes hot air.


Would a pilot light on a gas furnace still work with a defective thermocouple?

Pilot light would work but the main burner would not as the thermocouple proves that there is a pilot light to fire. The main gas valve would not open


What is air blast burner?

An air blast burner is a burner where a controlled blast of air is supplied the gas. The burner has an air blast type fuel injector.


How does an oil burner work?

Oil burner magic!!


How do you detect a crack heat exchanger in a furnace?

The most comon way to detect a crack in a heat exchanger is with a visual inspection, removal of the burner assembly and the use of a mirror and flash light. Or a smoke bomb test. A special little smoke bomb is placed in the burner area with the burners OFF. The blower is runnig and you light the smoke bomb, the smoke will draft up the flue vent or if a crack or rust hole is present then the smoke will get sucked into the air stream and come out of the duct work. Other than that using a carbon monoxide detector to see what the CO levels of the furnace are and comparing them to the supply air of the furnace to verify that there is no CO present in the air stream. The best and most accurate way is to contact a local Heating and Air Conditioning specialist or your local gas company should come out and perform a CO test on the furnace. Good Luck and God BLess

Related Questions

Why does a high efficiency furnace main burner shut off?

A high efficiency furnace main burner shuts off to prevent overheating and ensure safe operation.


Can the fan timer control board on a York furnace cause the furnace to continue running with the burner in operation?

yes it can fan


Why does the furnace main burner shut off after ignition?

The furnace main burner shuts off after ignition to maintain a safe and consistent temperature within the heating system. This helps prevent overheating and ensures efficient operation of the furnace.


Why does the furnace main burner shut off intermittently?

The furnace main burner may shut off intermittently due to issues with the thermostat, a dirty air filter, a malfunctioning flame sensor, or a problem with the gas supply. It is important to have a professional technician inspect and diagnose the issue to ensure safe and efficient operation of the furnace.


What is the function of the flame sensor on a furnace and how does it contribute to the safe and efficient operation of the heating system?

The flame sensor on a furnace detects the presence of a flame when the burner is ignited. It ensures that the burner stays lit and shuts off the gas supply if no flame is detected, preventing gas leaks and potential hazards. This contributes to the safe and efficient operation of the heating system by ensuring that the furnace operates properly and does not pose a risk of fire or gas leaks.


Why does the furnace ignitor light up but there is no flame?

The furnace ignitor may light up but not produce a flame due to issues such as a clogged burner, a faulty gas valve, or a lack of fuel supply. It is important to have a professional inspect and repair the furnace to ensure safe and efficient operation.


What could be causing the banging noise coming from my furnace?

The banging noise from your furnace could be caused by a variety of issues, such as a dirty burner, loose ductwork, or a malfunctioning blower motor. It is recommended to have a professional HVAC technician inspect and diagnose the problem to ensure safe and efficient operation of your furnace.


What is the function of a flame sensor in a furnace and how does it contribute to the safe and efficient operation of the heating system?

A flame sensor in a furnace detects the presence of a flame. It ensures that the burner is lit and functioning properly. If the sensor does not detect a flame, it shuts off the gas supply to prevent a buildup of gas. This contributes to the safe operation of the heating system by preventing gas leaks and potential hazards. Additionally, the flame sensor helps the furnace operate efficiently by ensuring that the burner is consistently lit, which maximizes the heating output and reduces energy waste.


Why does a high efficiency furnace's main burner shut off?

A high efficiency furnace's main burner shuts off to maintain a consistent temperature in the home and prevent overheating.


What is the correct oil burner nozzle on a ABC model P-712?

That depends on what the burner is installed in. One particular burner can be used on a multitude of boilers/furnaces simply by changing the nozzle to regulate both gph and flame pattern to suit the application. Contact the boiler/furnace mfr or check the installation/operation manual for the boiler/furnace for help. Lastly if that is of no help or not possible a good oil burner mechanic could help you out once he sees your entire application.


Where is the limit switch located on a furnace?

The limit switch on a furnace is typically located near the heat exchanger or burner chamber. It is a safety device that monitors the temperature inside the furnace and shuts off the burner if it gets too hot.


What is the purpose of the limit switch in a Lennox furnace and how does it contribute to the overall functionality of the system?

The purpose of the limit switch in a Lennox furnace is to monitor the temperature inside the furnace. It helps prevent the furnace from overheating by shutting off the burner if the temperature exceeds a safe level. This contributes to the overall functionality of the system by ensuring safe and efficient operation, protecting the furnace from damage, and maintaining a comfortable temperature in the home.