0
What else can I help you with?
What is an ir emitter?
Depending on context, it could be an infra-red emitter. An emitter that emits at a wavelength longer than that of visible red. infra red emitter is a special pn juction device in which emitter region emits infrared rays
In a common emitter transistor the primary purpose of a resistor connected to the emitter is to?
The emitter resistor in a common emitter configuration provides negative feedback to the transistor, reducing both its voltage gain and distortion.
When an NPN transistor is properly biased then most of the electrons from the emitter -?
Emitter
Why is collector current slightly less than emitter?
The percentage of doping in emitter is higher than collector region.hence large current is flow to emitter than collector.
What is a beta emitter?
In physics, an alpha emitter is a radioactive substance which decays by emitting alpha particles.
IS there an emitter in the univeres?
There are many emitters in the universe. For example, the Sun is an emitter of electromagnetic waves and certain types of particles. It would help if you were more specific.
What is emitter follower?
A: When a signal is not amplified but simply taken from an emitter the reason is that the emitter will provide better current capabilities
Why base in grounded in common emitter transistor as amplifier?
With a common emitter amplifier it's the emitter that is usually grounded.
What is an ir emitter?
Depending on context, it could be an infra-red emitter. An emitter that emits at a wavelength longer than that of visible red. infra red emitter is a special pn juction device in which emitter region emits infrared rays
What is the difference between a CB amplifier and CE and emitter-follower?
I think you mean a common emitter amplifier, which is an amplifier of voltage. Emitter-follower or common collector amplifiers are used to match impedances, or to amplify power or current. The emitter-follower is a type of common emitter circuit that has a resistor between the emitter and ground. The output signal is taken from the point between the emitter and its resistor.
In a common emitter transistor the primary purpose of a resistor connected to the emitter is to?
The emitter resistor in a common emitter configuration provides negative feedback to the transistor, reducing both its voltage gain and distortion.
When an NPN transistor is properly biased then most of the electrons from the emitter -?
Emitter
What do you mean by common emitter configuration and biasing pnp transistors?
A common emitter BJT transistor has the emitter ground. So u measure input voltage at base with respect to the ground, i.e; emitter and also u measure the output voltage at collector with respect to the ground, i.e; emitter. Hence, the emitter is common and thus the name.
Why would there be a gain when you add the emitter capacitor to a circuit board?
A capacitor has lower resistance (impedance) as frequency increases. Adding an emitter capacitor effectively lowers the emitter resistance as frequency increases. Since gain in a typical common emitter amplifier is collector resitance divided by emitter resistance, this decrease in emitter resistance will increase gain as frequency increases.
What is the advantage of emitter follower?
The advantage of the emitter follower is that it has a positive gain of 1.
Why output of common emitter amplifier is inverted?
In a common emitter amplifier, the base-emitter current causes a corresponding collector-emitter current, in the ratio of hFe (beta gain) or collector resistance over emitter resistance, which ever is less. Since this ratio is usually greater than one, the differential collector current is greater than the differential base current. This results in amplification of the base signal. As you increase the base-emitter current, the collector-emitter current also increases. This results in the collector being pulled towards the emitter, with the result that the differential collector voltage decreases. This results in inversion of the base signal.
Why emitter follower is called so?
Because of the geometry of the common collector configuration, changes in base voltage appear at the emitter. Said another way, what happens at the base pretty much happens at the emitter, and the emitter can be said to "mirror" or "follow" the base. The emitter is a follower of the base, and the name emitter follower appeared and was used.
