0
An electric circuit typically requires three essential parts to function: a power source (such as a battery or generator), a load (like a light bulb or motor that uses the electricity), and conductors (wires) to connect the components and allow the flow of electric current. Additionally, a switch may be included to control the flow of electricity. These components work together to create a complete circuit that enables the flow of electric current.
What else can I help you with?
How do you test a closed circuit?
we can make an open circuit by disconnecting the wire or break the circuit and a closed circuit is made by connecting all wires with the contents of the circuits.
How do you make a circuit so the lights can be turned on and off separatley?
To design a circuit so that lights can be turned on and off separately, we connect the circuit in parallel.
Where do you put your leads when checking continuity on a series circuit?
When checking continuity in a series circuit, you put your leads in series with the circuit or device being checked. You also make sure the circuit is deenergized and that it is open.
What is the history of the electric circuit?
the history of the electric circuit is that the person who made it his name is jack kilby but the history is that the electric circuit was one of the easiest way was to make the electric circuit when the electricity went out. THE END
In a series connection if one component fails the whole circuit fails?
Yes. Open circuit. A: It depends on the failure type a short will not necessarily make an open circuit but rather a non functional circuit.
How do you make an elctric dragon on Dragon City?
you buy the egg
What general apparatus anyone require to make a complicated electrical circuit?
A circuit can be classified as a voltage source connected to a load.
What are fenders?
Fenders are a brand of guitar, they make elctric acoustic and bass guitars as well as amplifiers and effects.
How do you adjust carb to make it leaner?
The only adjustment that you can lean out would be the idle circuit. That would be done by adjusting the idle mixture screw(s) while monitoring the vacuum and or the engine rpms. To make a carburetor run lean would require changing internal parts such as the jets and metering rods.
Yes this will. It does require some fitment parts for a proper installation. Give us a call at 800-854-5821 and we can make a bundle package for you.?
Yes this will. It does require some fitment parts for a proper installation. Give us a call at 800-854-5821 and we can make a bundle package for you.
What purpose might the multimeter serve in maintaining and troobleshooting a computer network?
With the multimeter you can measure the voltage on parts of the circuit board. You can also measure the resistance of resistors and make sure there are no short circuits in the circuit.
What happens if you gnaw on wires?
in some cases there have been elctric shocks whereas in other cases if you make a wish at the right point then you can become superman
All circuit boards contain microchips?
Circuit board is the name for the place / board that parts are put on to to make a circuit. All circuit do not have to have a microchip but that board will not do anything fancy. A speaker crossover for example is the only thing I can think of. All micro chips will need a circuit board to connect power, inputs, outputs, or just to mount into a package.
What does SMT mean when talking about electronic circuits?
SMT stands for Surface Mount Technology. It's a way to make a circuit board by placing the parts directly on the circuit board. The board is pre-printed to show exactly where to mount the parts, kind of like a child's puzzle where underneath each piece is a picture of the piece that should go over top of it. SMT has mostly replaced Through-hole Technology, which was where the parts attached to the circuit board using wire leads that would fit through holes in the circuit board.
What are the parts of an electrical current?
A flow of electrons is needed to have a current. And there (usually) must be a complete circuit. And you need a voltage to make the current move around your circuit. All tied up in Ohms Law - which I'll leave to you.
What function in a circuit for a switch?
A switch is a make - break device. Its function is a circuit is to make and break the current flow of the circuit that it is in. This action then starts and stops the load that is connected in the circuit.
Is anode the electron-providing electrode?
Yes, anode the electron provides electrode. It is stated that an electrode is a conductor that is used to make contact with non-metallic parts of a circuit.
