answersLogoWhite

0

This sounds like a homework question. Hint, define your parameters, and ask where the force is applied.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Engineering

What force is needed to bend 20 mm high tensile steel?

To know the force, you need to know how much you want to bend it; you also need to know the dimensions of the plate and how it is supported.


What is heavier a steel beam or concrete beam?

Steel is heavier than concrete for the same volume, however steel buildings are generally lighter. This is because steel buildings utilize high strength of steel, so volume of steel in steel buildings is much smaller than volume of concrete in concrete buildings. In another words in steel buildings much less volume of material is needed for the same strength compared to concrete buildings.


How much steel reinforcement used 1KN?

The steel reinforcement used will depend on several factors. Column length, beam length, and the column and beam cross section all depend on how much steel will be needed.


How do you unclog a bathroom face bowl?

Place a bucket beneath the 'U' bend to catch any water, and undo the pipe joints to remove the 'U' bend. Clean the pipes and 'U' bend as much as possible, before replacing the 'U' bend and tightening the joints (usually by hand if the pipes are plastic).


How much work must you do to push a block of steel across a steel table at a steady speed of 1.30 ms for 4.70 s?

Work = (force) times (distance)We've got the distance through which the block is pushed: (1.3) x (4.7) = 6.11 meters .Now, in order to calculate the work it takes to do the pushing, we need to know the force that was used.On this subject, the question is strangely silent, and no solution is therefore possible.

Related Questions

What force is needed to bend 20 mm high tensile steel?

To know the force, you need to know how much you want to bend it; you also need to know the dimensions of the plate and how it is supported.


How much force to bend a 25mm diameter bright steel bar that is 1500mm long and the force is applied in the middle of the bar?

The force required to bend a steel bar depends on the material's properties and the bending process. However, for a rough estimate, you can use the formula: Force = (3 * E * I * L) / (2 * r^2), where E is the Young's modulus, I is the area moment of inertia, L is the length of the bar, and r is the radius of the bar.


What force is needed to bend 1.5 inch square in tubing?

it depends on both the tube wall thickness and the length of the bend and how much you bend it. Otherwise you cannot determine force.


How much force is required to bend or dent steel?

This is a completely unanswerable question, as it depends on several factors: the composition of the steel in question (there are a great many different alloys that go under the colloquial name "steel"), the type of force being applied (tension, compression, etc.), the design geometries of the object in question, and the environmental factors around the steel (primarily, but not exclusively, the temperature)


How much force does it take to bend aluminum spoon?

The amount of force needed to bend an aluminum spoon will vary depending on the thickness and alloy of the aluminum. Generally, a moderate amount of force is required to bend an average aluminum spoon by hand.


Is wood the strongest material in an earthquake?

No. Steel reinforced structures are best as steel is much stronger than wood but can still bend without breaking.


How much force is required to crush an steel beverage can?

60060


Why does cycle rim dont bend even in heavy loads?

The spokes distribute the load throughout the rim. Here's how : Make a small ring of a thin steel wire. Hold it between your finger and thumb, and press. It will bend. Now, tie a straight piece of steel wire diagonally, and press the ring at the ends of the straight wire. You will need much more force. But, the same ring will bend with lower force, if you press it at points where straight wire is not there. Now, tie many such straight wires on the ring, and then press the ring. 'hope you got the picture clear :)


How much force does it take to bend the rear bumper of a 1990 ford bronco?

200 Newtons


How much does Subaru legacy weigh?

The 2009 Legacy Sedan 3350-3625, depending on exact equipment and transmission.


How much does one gram platinum price in rupees on 29 April 2011?

3625 in india per gram :P


How can you increase the break out force of bucket and arm of a Massey furgeson 1575 back hoe?

About the only way to increase the force applied is to increase the outflow of the hydraulic pump. An increase in p.s.i. should boost the force applied to the rams. You're going to have to be careful that you do not blow hoses or rams or bend steel if you raise the power too much. These systems are engineered to run on available p.s.i. and increasing it could be too much for the bucket/ram assembly.