0
What else can I help you with?
What is the significant relationship of the no load loss in excitation current test in transformer?
The no load losses are the losses caused by energizing the transformer. These are constant losses, regardless of loading. This in effect tells you the efficiency of the transformer. (Power in) - (no load losses) = (Power out)
What is the characteristics for a generator on a full load?
What characteristics are you looking for? At full load, a synchronous generator will be spinning at synchronous speed, providing real power (watts), and likely some reactive power (vars), or it may be taking reactive power from the system to help hold the system voltage down under light loading conditions.
What is ring power distribution?
In ring power distribution power is distributed in a ring where each point gets power from both the directions. The main advantage of a ring system is the reliability is high because if one link is broken power can be still be delivered from the other link.
What action can be taken if an industrial consumers power factor is too low?
The deterioration of the power factor in an industrial setting is almost always the result of running a lot of motors ... that is, a lot of inductive loading. That's corrected by adding utility capacitors across the lines, at the transformer that feeds the industrial plant. The power enters the plant with a big leading power factor, which compensates for all the lagging loading of the motors inside.
What is one disadvantage of an amplitude modulation communication system?
One disadvantage of the standard amplitude modulation system is that 67% of the power is used for the carrier, but the carrier transmits no information, so it can be considered as wasted power.The 34% remaining power is split between two mirror opposite sidebands so, in effect, you really only have 17% of your power used to carry the signal.
What is when computer is turned on and the operating system is loading?
I'm pretty sure that's the POST or the Power On Self Test.
Is when the computer is turned on and the operating system is loading?
operating system is not a loading, When is trun on system(press the power button). first of checked all the hardware devices,for exmple hard disk,ram,rom and etc. When the all devices dected process further. Jsb
What is the difference between between direct loading and phantom loading?
In phantom loading,less power is consumed as the current and voltage coils are connected seperately;but in direct loading a load is connected which draw a considerable power.
When retrieving a boat at a ramp what should be avoided?
power loading onto the trailer
Is an operating system and power point Computer hard wares?
No. Operating systems and Power Point are examples of computer software.
Mention the septs In booting?
The 7 steps of booting process in a computer are: Power On BIOS POST (Power-On Self-Test) Bootloader Execution Operating System Loading Kernel Initialization System Initialization User Login.
How does the solar system effect earth?
the solar system contains satellites that provide "solar power"
What is the process of loading an operating system into a computer's memory is called?
The process of loading an operating system into a computer's memory is called booting. During booting, the computer's firmware, typically the BIOS or UEFI, initializes hardware components and locates the operating system stored on a storage device. It then loads the OS into RAM, allowing the system to start and run applications. This process can be broken down into several stages, including POST (Power-On Self-Test) and the loading of the bootloader.
What is the Process of loading operating system software into a computer main memory from disk?
The process of loading operating system software into a computer's main memory from disk begins when the computer is powered on and the BIOS or firmware performs a power-on self-test (POST). Afterward, it locates the bootloader on the bootable disk, which is responsible for loading the operating system. The bootloader reads the operating system files from the disk and transfers them into the main memory (RAM). Once loaded, the operating system initializes hardware components and prepares the system for user interaction.
After a technician has assembled a new computer it is necessary to configure the bios at which point must a key be pressed to start the bios setup program?
On power-up. You need to tap the escape key to stop the operating system loading, and enter the BIOS set-up screen.
How do you add up scores when you have made a game on power point?
There is no system for adding up the scores in Power point. It is not made for game creation.
What is meant by the term POST power of self test?
Power On Self Test - is a series of diagnostic operations a computer performs when the power switch is pressed. This includes loading the operating system, peripheral handshakes and memory tests.
