answersLogoWhite

0

A phase-shift oscillator is a linear electronic oscillator circuit that produces a sine wave output.

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Engineering

What is the phase shift between voltage and current when an capacitance is connected to the circuit?

The amount of phase shift depends on the resistance that is also present in the system. In an ideal situation, the phase shift would be +90 degrees, but that would require a voltage source with zero resistance, conductors with zero resistance, and an ideal capacitor that exhibited only capacitance.


Would a 10 ohm resistive load or a 10 ohm reactive load produce the larger shift of theta in the primary of a transformer?

A 10 ohm reactive load would produce a larger shift of theta in the primary of a transformer compared to a 10 ohm resistive load. This is because a reactive load introduces a phase difference between the voltage and current, resulting in a larger reactive power component in the primary winding. In contrast, a resistive load maintains a phase angle of zero, leading to a smaller shift in the overall current phase. Thus, the presence of reactance in the load increases the complexity of the magnetic coupling in the transformer, causing a greater phase shift.


For AC circuits what is meant by the term in phase?

Both the current and voltage are represented by sine waves. In a pure resistive circuit the current and voltage wave forms would have the positive and negatives peaks and zero crossings perfectly aligned with the other waveform. If they were 180 degrees out of phase the positive cycle peak of one would align with the negative peak of the other and would be producing zero power. In between a zero and 180 degree phase shift the Power Factor would range from 1 with zero phase shift to zero with 180 degree phase shift.Power = Current x Voltage x Power Factor.Another AnswerFor a three-phase supply, the term 'phase' describes any one of the armature windings; for a three-phase load, the term 'phase' describes any one of the three loads. The three energised conductors that join the load to the supply are called 'lines'.So phase voltages are the voltages appearing across individual armature windings or loads, whereas line voltages are the voltages appearing across a any pair of line conductors.


What is the Phase resistance of 500 voltage?

Phase resistance refers to the resistance encountered by current in a single phase of a multi-phase system, such as a three-phase electrical system. It is not directly determined by the voltage level, like 500 volts, but rather depends on the characteristics of the load and the conductors in the circuit. To determine the phase resistance, one would typically need to know the current flowing through the phase and the power factor of the load. If you have specific details about the load or system, I can help calculate or explain it further.


How many degrees of current flow is there in a sine wave?

If you have V = 120Vrms Cos(2*pi*60t + 120). The magnatude of the voltage is 120Vrms. The frequency is 60Hz. The phase shift is 120. That would be the voltage that comes out of a standard American household eletrical outlet. The current would depend on what is plugged into the outlet. A general equation would be VmCos(w*t + theta) or ImCos(w*t + theta) for current. To use a Sine wave, just do a 90 degree phase shift. (sin(t) = cos(t-90) or cos(t) = sin(t+90))

Related Questions

What happens if two phases short with one phase with phase shift of one degree?

guess the fuse would blow


What is the phase shift between voltage and current when an capacitance is connected to the circuit?

The amount of phase shift depends on the resistance that is also present in the system. In an ideal situation, the phase shift would be +90 degrees, but that would require a voltage source with zero resistance, conductors with zero resistance, and an ideal capacitor that exhibited only capacitance.


Which signaling systems would you recommend for a situation in which bandwidth is limited and noise interference is a consideration?

Phase shift keying Quadrature shift keying


Difference between line transformation ratio and transformation phase ratio?

line transformation ratio would be the turns ratio (ie voltage ratio), while the phase transformation ratio is most probably the phase shift introduced by a 3 phase transformer.


Would a 10 ohm resistive load or a 10 ohm reactive load produce the larger shift of theta in the primary of a transformer?

A 10 ohm reactive load would produce a larger shift of theta in the primary of a transformer compared to a 10 ohm resistive load. This is because a reactive load introduces a phase difference between the voltage and current, resulting in a larger reactive power component in the primary winding. In contrast, a resistive load maintains a phase angle of zero, leading to a smaller shift in the overall current phase. Thus, the presence of reactance in the load increases the complexity of the magnetic coupling in the transformer, causing a greater phase shift.


For AC circuits what is meant by the term in phase?

Both the current and voltage are represented by sine waves. In a pure resistive circuit the current and voltage wave forms would have the positive and negatives peaks and zero crossings perfectly aligned with the other waveform. If they were 180 degrees out of phase the positive cycle peak of one would align with the negative peak of the other and would be producing zero power. In between a zero and 180 degree phase shift the Power Factor would range from 1 with zero phase shift to zero with 180 degree phase shift.Power = Current x Voltage x Power Factor.Another AnswerFor a three-phase supply, the term 'phase' describes any one of the armature windings; for a three-phase load, the term 'phase' describes any one of the three loads. The three energised conductors that join the load to the supply are called 'lines'.So phase voltages are the voltages appearing across individual armature windings or loads, whereas line voltages are the voltages appearing across a any pair of line conductors.


Device for connecting two or more computers by phone?

That would be called a Modem. A Modem is an acronym for MOdulator, DEModulator. There are two technologies used for computer modems; tone shift and phase shift. Tone shift takes the ones and zeroes and turns them into tones, and support speeds up to 9600 baud (9600 bits per second, roughly). Phase shift takes the ones and zeroes and turns them into phased tones, and supports speeds of up to 56KBaud (56 thousand bits per second).


Describe in brief the type of power factor improvement system?

You want a power factor of 1 or 100%, which is a purely resistive circuit. If you have a motor or some other inductive load in a circuit the total voltage and total current in the circuit will not be in phase (phase shift), your power factor will be less than 1. By adding a capacitor (180 degrees out of phase with inductive load) to the circuit that has a capacitive reactance equal to the inductive reactance of the motor, you can cancel the phase shift and have an ideal power factor (no wasted power). Anything above .9 would be good.


What is the Phase resistance of 500 voltage?

Phase resistance refers to the resistance encountered by current in a single phase of a multi-phase system, such as a three-phase electrical system. It is not directly determined by the voltage level, like 500 volts, but rather depends on the characteristics of the load and the conductors in the circuit. To determine the phase resistance, one would typically need to know the current flowing through the phase and the power factor of the load. If you have specific details about the load or system, I can help calculate or explain it further.


Will a 1997 Dodge truck automatic transmission fit a 1995 Dodge truck?

It would bolt up, but it will not shift. The shift control systems are different.It would bolt up, but it will not shift. The shift control systems are different.


Is 3 phase motor run on 1 phase supply?

No. That would be a single phase motor.


What is meant by Phase Shifting?

Phase shifting basically means moving the reference from where the wave starts along x axis. For example, sine wave and cosine wave are basically similar, but have different starting points along x axis. Therefore, it's clear that shifting a sine wave by 90 degree towards negative infinity will give cosine wave.