0
What else can I help you with?
How many ohms is a computer speaker?
There is no single standard. Many computer speakers are rated at 8 ohms while others are 16 ohms or higher. My computer subwoofer here is 4 ohms.
What is the total power in a circuit with a current of 4 A and a resistance of 12 ohms?
In DC circuits, V = I / R, and P = V*I You can use these to get P = I^2 * R = (4)^2 * 12 = 192 watts.
If an amplifier is AC 220Watt and 12 DC so up to how many watts or ohms speakers you can use on it?
Your question doesn't fully make sense. Let me see if I can answer part of it. If your amp puts out 220 watts, the speakers should be rated for at least 220w, or they may be destroyed if you turn the amp all the way up. Watts are a measurement of power, in the case of speakers they are rated for how much power (watts) they can handle. Ohms is a different thing altogether. Ohms are a measurement of resistance to electrical flow. Amps are usually rated to work with certain impedance level speakers (4 ohm, 8ohm, 16ohm, etc.) the lower the ohms, the harder the amp works. I know it seems backwards but it isn't. each amp is different so you would have to read the amp's spec sheet to see what they reccomend. I have no idea what you are asking for with the "12 DC" thing.
How do you convert 8 ohms to 4 ohms?
wire two 8 ohm speakers in a parallel circuit!
Five resistors are connected together in series One resistor is 2 ohms one is 3 ohms one is 4 ohms one is 5 ohms and the fifth is 6 ohms What is the total resistance?
Purely additive. 2+3+4+5+6=20.
How many watts does the Rockford Fosgate Power 150a1?
75 x 1 Watts RMS @ 4 Ohms 150 x 1 Watts RMS @ 2 Ohms
How many ohms in 800 watts?
To calculate the resistance in ohms, you also need to know the voltage. The formula to find the resistance in ohms is R = V^2 / P, where R is the resistance in ohms, V is the voltage, and P is the power in watts.
You have an Alpine type X 1243D subwoofer you are trying to decide if running it at a 2ohm load at max power or a 4ohm load at two thirds of its power range will work better?
Multiple subs wired together must be the same coil type and impedance. If they’re not, the power won’t divide evenly between them, and some subs would probably be over-powered while others get under-powered. If you want to run different types of subs in a system, each type needs to have its own separate amp. Then, multiply the number of subs you have by the RMS rating of each, to get their total RMS rating. You want to make sure the amp you choose will supply no more than the sub system’s total RMS rating. Figure out the possible total impedance(s) that the subs can be wired together to form. (SVC = single voice coil, 1 pair of terminals; DVC = dual voice coil, 2 pairs of terminals.) 1 SVC 2-ohms can only have 2 ohms of impedance 1 SVC 4-ohms can only have 4 ohms of impedance 1 DVC 2-ohms can have 1 ohm or 4 ohms of impedance 1 DVC 4-ohms can have 2 ohms or 8 ohms of impedance 2 SVC 2-ohms can have 1 ohm or 4 ohms of impedance 2 SVC 4-ohms can have 2 ohms or 8 ohms of impedance 2 DVC 2-ohms can have 2 ohms or 8 ohms of impedance 2 DVC 4-ohms can have 1 ohm or 4 ohms of impedance 3 SVC 2-ohms can have 6 ohms of impedance 3 SVC 4-ohms can have 1.3 ohms of impedance 3 DVC 2-ohms can have 1.3 ohms or 3 ohms of impedance 3 DVC 4-ohms can have 2.7 ohms or 6 ohms of impedance 4 SVC 2-ohms can have 2 ohms or 8 ohms of impedance 4 SVC 4-ohms can have 1 ohm or 4 ohms of impedance 4 DVC 2-ohms can have 1 ohm or 4 ohms of impedance 4 DVC 4-ohms can have 2 ohms or 8 ohms of impedance Look for an amplifier that can put out power up to the RMS wattage at an impedance load the subs can be wired to form. 8 ohms — figure on the amp putting out half the power it would at 4 ohms 6 ohms — figure on the amp putting out three-quarters of the power it would at 4 ohms 3 ohms — figure on the amp putting out the average of what it would at 2 ohms and at 4 ohms 2.7 ohms — figure the same as for 3 ohms, and add a few watts 1.3 ohms — use the 1-ohm spec and take away a few watts Example: You have two Alpine S Series S-W8D4 8" subwoofers and you want the right amp for them. They are DVC 4-ohm subs rated at 300 watts RMS each. Two 300 watts RMS subs together need a maximum total of 600 watts RMS. Using the chart in Step 2, 2 DVC 4-ohm subs can be wired together to form a 1-ohm, a 4-ohm, or a 16-ohm load. The last is too high a load to be practical, so you’ll look for an amp that can put out up to 600 watts RMS into either a 4-ohm load, or a 1-ohm impedance load: up to 600 watts RMS x 1 at 4 ohms, or up to 600 watts RMS x 1 at 1 ohm Among Crutchfield’s selection of amplifiers you’ll find: Memphis Audio PRXA600.1 — 600 watts RMS x 1 at 1 ohm JL Audio JD1000/1 — 600 watts RMS x 1 at 4 ohms Kicker KEY500.1 — 500 watts RMS x 1 at 1 ohm Any one of these high-quality amplifiers would work well with those subs. It doesn’t matter which impedance an amp plays through — 600 watts RMS through a 4-ohm load produces the same volume as 600 watts RMS through a 1-ohm load. You have a Memphis Audio SRX500D.1 amplifier and you want it to drive two subwoofers The amp is capable of 350 watts RMS x 1 at 4 ohms and 500 watts RMS x 1 at 2 ohms. Let’s say you choose to maximize the amp’s potential and want the system to put out 500 watts RMS. This means your subs have to be wired to form a total impedance of 2 ohms. Two subs on a 500 watts RMS amp will want about 250 watts RMS each. So you’ll look for subs each rated for 250 watts RMS or more. Using the chart in Step 3, for two subwoofers, a final 2-ohm load can be achieved with either two SVC 4-ohm subs or two DVC 2-ohm subs. So, you’ll look for two subs that are either SVC 4-ohms or DVC 2-ohms, rated for at least 250 watts RMS each: 2 SVC 4-ohms, at least 250 watts RMS, or 2 DVC 2-ohms, at least 250 watts RMS Among Crutchfield’s selection of subwoofers you’ll find: You have a Memphis Audio SRX500D.1 amplifier and you want it to drive two subwoofers The amp is capable of 350 watts RMS x 1 at 4 ohms and 500 watts RMS x 1 at 2 ohms. Let’s say you choose to maximize the amp’s potential and want the system to put out 500 watts RMS. This means your subs have to be wired to form a total impedance of 2 ohms. Two subs on a 500 watts RMS amp will want about 250 watts RMS each. So you’ll look for subs each rated for 250 watts RMS or more. Using the chart in Step 3, for two subwoofers, a final 2-ohm load can be achieved with either two SVC 4-ohm subs or two DVC 2-ohm subs. So, you’ll look for two subs that are either SVC 4-ohms or DVC 2-ohms, rated for at least 250 watts RMS each: 2 SVC 4-ohms, at least 250 watts RMS, or 2 DVC 2-ohms, at least 250 watts RMS Among Crutchfield’s selection of subwoofers you’ll find: Alpine W10S4 10" — SVC 4-ohm, 250 watts RMS JL Audio 12W0v3-4 12" — SVC 4-ohm, 300 watts RMS Kicker 44CWCS104 — SVC 4-ohm, 300 watts RMS Rockford Fosgate R2D2-10 10" — DVC 2-ohms, 250 watts RMS Hope this helps! (:
If you have two 150 RMS watt subs on the same ch of an amp What is the RMS watts needed from the amp?
Depends on the impedance of each speaker. If they are car subs and not converted home speakers, they are probably 4 Ohms each. Depending on how you wire them you get either 8 Ohms or 2 Ohms. 8 Ohms is not a problem load-wise for the amp, but if it is rated at 100 watts into 4 Ohms, then you will only get 50 watts into 8. Many car subs nowadays will handle a 2-Ohm load, but some will not. Your two speakers will handle 2x150 watts or 300 watts. An amp that is rated to drive 300 watts into 4 ohms will either deliver more like 500 watts into 2 Ohms, or it will melt through the floor of your car. So you need to look up the specs for your amp in the instruction manual. If it will only run into a 4-Ohm load, you can only use one 4-Ohm sub per channel. If it will handle a 2-Ohm load, you will have to turn it up slowly or you will blow your speakers out. Mr Ohm and his law will not be denied.
How much ohms does 1500 watts speaker has?
The wattage and ohms of a speaker are not related; the resistance for speakers is usually 4 or 8 ohms.
How many watts is a kicker impulse 352xi amp?
The Kicker Impulse 352xi amp has a maximum power output of 35 watts per channel x 2 channels at 4 ohms or 35 watts x 2 channels at 2 ohms.
How many watts is alpine v12 mrv-f505 amplifier?
The Alpine v12 MRV-F505 amplifier puts out up to 200 watts of RMS power at 4 Ohms and using 12 volts. At 14 volts, it puts out up to 400 watts of RMS power with a bridged 4 Ohms ratio.
What do the subwoofers ohms for?
the ohm is a unit of measurement based off of someones last name. When used in subwoofers, for example 4 ohms or 8 ohms, it actually determines the amount of watts the speaker needs. Like if two identical subwoofers were taken and one was 4 ohms and one 8 ohms and applied say 150 watts to each of them, the 4 ohm would be louder because ohms are the speakers resistance and the lower the ohms the less amount of power it takes for the subwoofer to reach a specific loudness. That's why professional huge subwoofers may be one ohm, because an amplifier that has less power than the sub could still power it because since its one ohm, the 500 watt amplifier at 4 ohms could be 1500 watts at 1 ohm.
How many watts does a sony xm752x amp put out?
The Sony XM752X amplifier can output up to 280 watts RMS per channel at 4 ohms, or 380 watts RMS per channel at 2 ohms, when both channels are driven with a 20Hz - 20kHz signal.
4 ohms equals how many watts?
Ohms does not equal watts. You need to know what voltage is across the resistor to determine how many watts it is drawing or how many watts the resistor should be rated for.Power is the voltage across the resistor SQUARED divided by the resistance. If this 4 ohm resistor has 12 volts across it then the watts power is (12 x 12) / 4 = 36 watts.1 Watt equals 1 Volt times 1 Amp.
How many watts is a Kenwood KAC-744 amp?
The Kenwood KAC-744 amp has a power handling capacity of 50 watts RMS per channel at 4 ohms.
How many watts is a titan hifonics txi4406 4x110?
The Hifonics TXi4406 amplifier is rated at 4 x 110 watts RMS at 4 ohms. This means each channel can output up to 110 watts of power into a 4-ohm load.
