answersLogoWhite

0

In a power supply diagram, the block that indicates a pulsating DC output is typically labeled as a "Rectifier" or "Rectifying Stage." This component converts the AC input voltage into pulsating DC by allowing current to flow only in one direction. The resultant output is not smooth and contains ripples, which distinguishes it from a pure DC output. Further filtering is usually required to smooth out these fluctuations.

User Avatar

AnswerBot

1mo ago

What else can I help you with?

Continue Learning about Engineering

What is the Frequency of pulsating dc?

The frequency of pulsating DC, often referred to as pulsating direct current, is determined by the rate at which the voltage alternates between its maximum and minimum values. In a typical scenario, this frequency corresponds to the frequency of the alternating current (AC) supply from which it is derived, such as 50 Hz or 60 Hz. Pulsating DC can be generated through rectification of AC, leading to a waveform that oscillates but does not alternate in polarity. The frequency of the pulsating DC is thus defined by the rectification process and any filtering applied to the output.


What is Supply voltage rejection ratio?

Supply Voltage Rejection Ratio (SVRR) is a measure of how well a circuit, typically an amplifier or regulator, can maintain its output stability despite variations in the supply voltage. It is defined as the ratio of the change in supply voltage to the resulting change in output voltage, often expressed in decibels (dB). A higher SVRR indicates better performance, as it means the output is less affected by fluctuations in the supply voltage, which is crucial for ensuring consistent operation in electronic systems.


Why you use capacitor in a power supply?

The result of rectifying AC into DC produces a pulsating DC voltage. This is usually not acceptable. Capacitors store some of the energy, and release it during the time when the recftified voltage falls to zero. This smooths out the pulsations and produces a relatively smooth, constant DC output.


How do you troubleshoot generator that fails to supply ac voltage?

You first use the schematic diagram in the equipment service manual to understand the flow of the power and signals in the generator. The first thing to check is all of the power supply voltages. If one is missing, the generator can fail in such a way as to produce no output. Then you can use an oscilloscope to trace the problem backwards, from the output connector of the generator to to the source of the signal generation.


When switch is off of power supply output shown on the multimeter is negative voltage from power supply?

Yes.

Related Questions

If the original power supply indicates an output 9v and 700mA and you use one that indicates an output of 9v and 2000mA will this disturb the performance of the machine a pedal effect or even ruin it?

No.


What is the Frequency of pulsating dc?

The frequency of pulsating DC, often referred to as pulsating direct current, is determined by the rate at which the voltage alternates between its maximum and minimum values. In a typical scenario, this frequency corresponds to the frequency of the alternating current (AC) supply from which it is derived, such as 50 Hz or 60 Hz. Pulsating DC can be generated through rectification of AC, leading to a waveform that oscillates but does not alternate in polarity. The frequency of the pulsating DC is thus defined by the rectification process and any filtering applied to the output.


Block diagram of thermal power station?

oil supply boiler turbine generator transformer electric output


Do transformers work on DC supply?

No, unless you have a pulsating DC


Why does my 12 volt direct current motor stutter when i connect it to a pulsating 12 volt direct current power supply?

Your 12-volt direct current motor may stutter when connected to a pulsating power supply due to irregular voltage levels that prevent the motor from receiving a consistent flow of power. Pulsating DC can lead to insufficient torque, causing the motor to struggle to maintain its speed and leading to stuttering. Additionally, the motor might not be able to handle the rapid fluctuations in voltage, which can result in erratic behavior. To resolve this, consider using a stabilized power supply that provides a smooth, constant voltage output.


What is Supply voltage rejection ratio?

Supply Voltage Rejection Ratio (SVRR) is a measure of how well a circuit, typically an amplifier or regulator, can maintain its output stability despite variations in the supply voltage. It is defined as the ratio of the change in supply voltage to the resulting change in output voltage, often expressed in decibels (dB). A higher SVRR indicates better performance, as it means the output is less affected by fluctuations in the supply voltage, which is crucial for ensuring consistent operation in electronic systems.


Supply's or supplies what is the correct spelling?

"Supplies" indicates the plural of supply, while "supply's" indicates ownership.


What is competitive supply?

There is competitive supply,if an increase in the output of one commodity requires a reduction in the output of another commodity.


Power supply units are rated in?

Power supply units are rated based on their output and efficiency. When more equipment is connected, a higher output power supply is needed.


Output DC power supply?

????????????????


How to draw a supply chain diagram?

no


Will government tax per unit of output reduces supply?

Yes; a government tax per unit of output reduces supply.